CDT835SMJ4DS General Electric Dishwasher - Parts

This lower rack roller is a genuine replacement component designed to support the smooth and stable movement of the dishwasher’s bottom rack. Measuring approximately 1.5 inches in diameter and finished in charcoal gray, it ensures consistent rack alignment and ease of use during loading and unloading. For optimal performance, it is recomm...Read moreended to replace all four rollers simultaneously. Installation is straightforward and requires no special tools, though wearing protective gloves is advised. Sold individually.

This dishwasher door latch is designed to secure the door during operation by connecting to the door strike and ensuring a tight seal. Mounted to the tub frame, it plays a critical role in enabling the appliance to run safely and efficiently. A damaged or faulty latch can prevent the door from staying closed, interrupting the wash cycle o...Read morer preventing it from starting altogether. This OEM replacement part is sold individually and does not include the door strike, which must be purchased separately if also worn or broken. Always disconnect the power supply before beginning installation.

The element heating assembly is found at the bottom of the dishwasher tub, and helps to warm the water in the wash cycle, and dry the dishes afterward. If the water does not heat up during the wash cycle, or the dishes are not being dried properly, you may need to replace the element heating assembly in your dishwasher. This element heati...Read moreng assembly is horseshoe-shaped and is sold individually. To replace your heating assembly, first make sure it has cooled down, then simply slide the connecting tabs out. Replace with a new heating element and your problem should be solved.

- Includes: 4 brackets, 4 roller wheel brackets, and 8 wheels part # WD12X26146 Dishwasher Lower Dishrack Carrier and Roller Kit (Set of 4). This kit will replace all four one piece roller carriers with two piece roller carriers. Match each carrier and cover designated for the side being replaced and replace all four carriers

This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the cabinet or countertop. This part is about 3 inches long and is made of metal. This kit does not include the screws, please order screws separately if necessary.

This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, ensuring stable and effective spray arm performance. Sold individually, this durable metal fastener requires a nutdriver for proper installation.

This is a drain pump kit for dishwashers. The drain pump for is responsible for pulling out and removing all contaminated food water from your dishwasher during and at the end of its washing cycle. If you notice water standing in your dishwasher after the cycle is over, or if you experience and notice leaks underneath your dishwasher, the...Read more pump will likely need to be replaced. This drain pump kit comes with the drain itself, as well as 5 different metal screw clamps of varying sizes. Replacing this drain pump will require some disassembly of your dishwasher, which means you will need a screwdriver, wrench, and protective equipment such as work gloves. This drain pump is sold as an individual OEM part, and does not come with any hoses or wire harnesses, so consider that before ordering.

Stop leaks and keep your dishwasher running smoothly with this tub gasket replacement. It forms a tight seal between the door and tub, so water stays inside during every wash cycle. Made from strong, flexible rubber, it’s built to last and easy to install—just remove the old gasket, clean the channel, and press the new one in. If you’ve n...Read moreoticed puddles on the floor or dishes that aren’t drying well, this simple fix can make a big difference.

This dishwasher latch strike is a manufacturer-approved replacement part for your appliance. The latch strike is an important component in your dishwasher door assembly, and adds an extra layer of security in keeping the door closed. This part may become damaged if the door has been opened during a wash cycle. It can also wear out over ti...Read moreme. It is fairly easy to replace, simply pop out the old door strike using a screwdriver for leverage, and insert the new one.

This circulation pump is a genuine OEM replacement part designed for select GE dishwashers. It plays a critical role in the cleaning process by continuously moving water throughout the appliance, ensuring consistent spray arm performance and thorough dishwashing. Proper circulation is essential for effective detergent distribution and rin...Read morese cycles. A malfunctioning pump may result in poor cleaning, unusual noises, or cycle interruptions. Always confirm compatibility using your dishwasher’s model number before purchasing. Installation should be performed with the appliance disconnected from power and water supply, and may require basic tools and reference to model-specific instructions.