CDE25P6W Crosley Dryer - Instructions

I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wednesday

1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall ... Read more when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)

First went and got a beer.
Looked at the dryer.
Drank my beer.
Went and got one more, due to long job.
Looked at dryer again.
Opened the door.
Had to get one more beer.
Removed filter.
Got one more cold one.
Put new filter in.
Got one more beer.
Closed door.
Finished!

Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcer ... Read more ting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.

The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in.

I opened the dryer from the front by pushing in on the two clips just under the top. I then had to remove two screws on each side and took the front panel off. I reached around underneath on the right side to slip the belt off the pulley. I pulled the drum out and then I could see the roller that was squeaking (the left one). The whee ... Read more l had sheared some of the support off and that was the cause of the squeak.

I took the locking ring off and removed the wheel and support. I put the new support in, attached it, and then the wheel, washer and lock ring. I used pliers to push the lock ring onto the support.

Then I put the drum back in making sure it was in all the way (it fits snugly between the wheel and the back of the dryer). The belt is a little tricky to get back on. I put it around the drum and then reached underneath and behind again. The pulley is on a spring, so you have to pull it up and put the belt on all one-handed and blind. Once that was on, I gave it a few turns to make sure everything was working again.

It is quiet as can be now!

I slid in the new one

Parts Select made it extremely easy to order parts from their site. Parts came in a timely manner and very reasonable priced. Thanks to Parts Select! Door Seal just needed to be removed and replaced by pushing into little slot openings.

Unplugged unit, lifted the top cover, removed heater element screw, lifted out element, lifted out thermal fuse bracket. Removed wires from thermal fuse, confirmed was open curcuit at room temperature. Attached wires to thermal fuse, inserted fuse into bracket, slid bracket onto clip on side of box that housed the heater element, reinst ... Read more alled heater elememt, inserted long screw into heater element hole and tightened snugly. Extra to ensure proper air flow: Then removed wires from door switch on fron panel (labeled them), removed 2 screws at top of from panel, tilted and lifted front panel off, removed blower cover, cleaned all duct work from blower to exit of unit, sealed plastic duct that was attached to front panel. It had loose gaskets that allowed air to be drawn in from the sides and not through the duct thus bypassing the drum and heater element. Reattached blower cover, lowered and tilted front cover into place, reattached top 2 corner screws, reattached switch wires, lowered top. Plugged in and tested.
Note the Partselect sales person told me that the LA-1053 kit contained 3 items, however, it only came with the fuse, not the thermostats. Foutunately, only my fuse was shot.

It was easy - I had my 12yr old daughter do it. The old door seal was completely removed, then you placed the new seal in the apropriate knoches that are on the door of the dryer. The lint filter just had to be placed in the vent. - Done.

First I removed the two screws that hold the element in place. I then pulled the element completely out and disconnected the two wires.

From there it was just a matter of installing the new part.

Anybody could do it

First of all, you go in from the front. There a clip on each side that I just pried up to pop the front of the dryer up. A screw also needs to be removed in the lint catcher area. Also, two screws holding the door open switch must be removed as I never could get the electrical connectors to disconnect. No big deal. I had to figure ou ... Read more t you must lift the front of the dryer up as the last two things holding it in are a prong on each side. Lift the front up and off and set it aside. As you do this the drum will either fall on your feet or you'll have it supported be another person or with something else. I used bungee cords and kept it in the laundry room. Cleaned out all the old lint, collected a few bucks in change. It took me awhile to figure out how the new belt routed through the removable pulley guide thing and around the wheel pulley. I don't remember right now as I'm not looking at it but remember pinching the belt and feeding it through the guide and around the wheel pulley which has a little slot and grooves matching the belt. Besides scrapping my wife's hand while she was helping me get the front of the dryer back on there were no casualties or further complications. Good luck!

Disconnected supply. Lifted top (hinges on rear). removed two 1/4 hex head screws retaining front panel. Disconnected door switch wires. Removed front panel, lifting off from bottom tabs. Lifted out drum and discarded broken belt. Spent 30 minutes+ cleaning interior, drum skid area, dryer exit tube, motor pulley, belt tensioner, etc, e ... Read more tc. Checked wiring harness for possible damage (no damage found). Repositioned drum skid pads, which had become dislodged from their intended position. Reinstalled the drum with new belt, ensuring both belt & tensioner were correctly positioned, and drum rollers and felt seals were also correctly positioned. Reinstalled front panel, tightening the two 1/4 hex head retaining screws. Reconnected power. Checked functionality. Closed top cover.

There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the ... Read more dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.

Turn the power off to the dryer. Pushed the two retaining clips that held the top of the dryer to the dryer sides. One on each side of the front. Table knife works really well to do this. Lift the top of the dryer up all the way. You will see the heating elements in the rear center of the dryer. There will be one screw holding the h ... Read more eating elements in place. Once you remove the wires from the heating element and remove the screw the heating element will lift out. Remove the heating elements and set down somewhere they will not get damaged. On the side the screw came out of there will be the heat fuse (as Maytag calls it). Remove the retainer by picking straight up on the retainer and the fuse will come out with the retainer. Remove the wires and replace the fuse and reinstall in reverse order.