CDE20T8A Crosley Dryer - Parts

This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the rotation of the motor to turn the drum. The belt attaches to the drum, idler pulley, and motor pulley.

This dryer heating element kit is 240 volts and 4750 watts. The function of the heating element is to produce the heat that allows you to dry your clothing during your dryer cycle. If your clothes take too long to dry, or if your dryer is not getting any heat or enough heat, you may need to replace your element. Before you begin your repa...Read moreir, make sure to disconnect the power from the dryer. The tools you will need for this repair include a putty knife, a quarter-inch nut driver, and a pair of needle nose pliers.

This screw is sold individually.

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and properly. If your clothes dryer has any of the following symptoms then replacing the clamp can be a solution: making loud noises, not producing enough heat or no...Read more heat at all, and/or clothes are taking too long to dry. Make sure to unplug thedryer from power source before installing this part and refer to the installation instructions provided by the manufacturer for further guidance.

The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four screws, one spacer, two washers, two retaining rings, two rear rollers, and two cylinder support shafts. The drum support roller kit may need...Read more to be replaced if the dryer is noisy or will not tumble. Important note: This kit has been updated by the genuine manufacturer to have one spacer that is the thickness of two spacers. Please search by model number to get these parts separately.

This screw is sold individually.

This blower wheel is suitable for some clothes dryers of the 10 and earlier series. Manufactured to fit a 1/2 inch motor shaft, this blower wheel is 3-1/8 inches deep. The diameter of the wheel is 7-1/8 inches, and the spring clamp is not included.

This high limit/safety thermostat is used on many gas and electric clothes dryers. It is made of metal, and is almost two inches long. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 258 degrees Fahrenheit. The element will kick back in when the temperature drops to 178 degrees Fahrenheit.

The drum felt seal, used in dryers, allows the drum to smoothly glide with minimal friction. If any of the following symptoms occur with your dryer, replacing the felt seal can be a solution to your problem: makes noises, does not tumble, takes too long to dry, not enough heat, or no heat at all. First take off the front panel of the drye...Read morer and remove the drum. Next, unscrew the old drum support wheels by following the instructions from the manufacturer manual. To get the retaining clips on, place them in front of the wheel shaft and clamp down on the clip and shaft as you snap it in. This part can be used for both the front and rear in some models. Remember to unplug your dryer from the power source before beginning this project.

This part is the replacement thermal fuse for your dryer. It measures a little more than an inch wide, and about ¾ inch long. The thermal fuse is a safety device that shuts off the burner in a gas dryer, or the motor in an electric dryer when the dryer overheats. If your dryer will not start, or if it is not producing any heat, you may ne...Read moreed to replace the thermal fuse. Be sure to disconnect power to the dryer before you begin this repair. This part is sold individually and is an authentic OEM part sourced from the manufacturer.

This part works in conjunction with the blower wheel.

This kit includes 2 glides (left and right), 2 pads with adhesive backing and 1 support brace.