CDE20M6A Crosley Dryer - Parts

This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the rotation of the motor to turn the drum. The belt attaches to the drum, idler pulley, and motor pulley.

This dryer heating element kit is 240 volts and 4750 watts. The function of the heating element is to produce the heat that allows you to dry your clothing during your dryer cycle. If your clothes take too long to dry, or if your dryer is not getting any heat or enough heat, you may need to replace your element. Before you begin your repa...Read moreir, make sure to disconnect the power from the dryer. The tools you will need for this repair include a putty knife, a quarter-inch nut driver, and a pair of needle nose pliers.

This screw is sold individually.

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and properly. If your clothes dryer has any of the following symptoms then replacing the clamp can be a solution: making loud noises, not producing enough heat or no...Read more heat at all, and/or clothes are taking too long to dry. Make sure to unplug thedryer from power source before installing this part and refer to the installation instructions provided by the manufacturer for further guidance.

The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four screws, one spacer, two washers, two retaining rings, two rear rollers, and two cylinder support shafts. The drum support roller kit may need...Read more to be replaced if the dryer is noisy or will not tumble. Important note: This kit has been updated by the genuine manufacturer to have one spacer that is the thickness of two spacers. Please search by model number to get these parts separately.

This screw is sold individually.

This high limit/safety thermostat is used on many gas and electric clothes dryers. It is made of metal, and is almost two inches long. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 258 degrees Fahrenheit. The element will kick back in when the temperature drops to 178 degrees Fahrenheit.

This part is the replacement thermal fuse for your dryer. It measures a little more than an inch wide, and about ¾ inch long. The thermal fuse is a safety device that shuts off the burner in a gas dryer, or the motor in an electric dryer when the dryer overheats. If your dryer will not start, or if it is not producing any heat, you may ne...Read moreed to replace the thermal fuse. Be sure to disconnect power to the dryer before you begin this repair. This part is sold individually and is an authentic OEM part sourced from the manufacturer.

Pad has adhesive backing.

This is a 120 volt, 25-watt light bulb that fits a variety of medium to large kitchen appliances. It functions by illuminating when the appliance door is open. It has a small base with a twist lock. This part is sold individually. This is a common wear part, so it is recommended order a spare and to check other appliance light bulbs in yo...Read moreur home. This is an authentic OEM part that is sourced directly from the genuine manufacturer. Be careful when handling the light bulb; use a pair of needle nose pliers to remove the base if the glass bulb is broken.

This screw is sold individually.

This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they are used with bolts and screws in order to hold items firmly together. This piece is a fastener that attaches one item to another. This part has several advantage...Read mores, the main one being that it is universal and can be used with most pieces and appliances in your home. This hex nut is an original equipment manufacturer part, meaning it is directly sourced from the manufacturer.