CDBEH960TS0A Frigidaire Dishwasher - Instructions

Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.

I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.

The hardest part was disconnecting the dishwasher. the motor is located on the bottom so after pulling it out and laying it down on the front of the machine the motor unplugs and 2 screws hold it in place.The new motor comes with "O" rings so I applied a little grease and put it back together. 2 minutes to replace motor, 15 minutes to dis ... Read more connect water and electric, 15 to reconnect.

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa ... Read more sher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

See posting under O rings. Get schematic Motor & Pump pg. 8 from pub # 5995487674. Steps: 1) run cycle so most water is pumped out of dishwasher 2) remove front cover to reduce weight of door; 3) disconnect electric plug, hot water hose [NOTE: be prepared for some water from hose], and waste tube all usually found under sink area; 4) remo ... Read more ve 2 screws at top of front panel; 5) lower leveling feet to allow best clearance; 6) put towels under front feet to protect floor and slide unit out from under counter; 7) place heavy blanket next to unit to protect floor and tip unit over on its side; 8) disconnect electric plug from motor and remove metal spring clip holding motor (2 torx screws) and pull clip off motor; 9)gently rock motor while lifting to remove from unit [NOTE position of motor for reassembly]; 10) put thin coat of silicon on O rings and place on new motor [look at old motor to make sure O rings are in proper slots; 11) line up motor and gently push new motor back into position; 12) reverse disassemble steps above. 13) run dishwasher through fastest cycle to check for leaks.

My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, ... Read more armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman

The Spray arm and the support had come off during operation and subsequently melted on the heating element. This was our fault, as a knife had slipped through the lower dish-rack and acted as a ramp to launch the spray arm as it came around. The support was a simple 1/4 turn counter-clockwise until it clicked into place, drop the strain ... Read more er basket into position around the support, them push the spray arm into place until the catches snap over the retaining ring molded into the support. All told, about 10 minutes, max.

Removed bottom plate and heating element brass nuts. Disconnected heating element. Connected new one then replaced brass nuts. Put bottom plate back on. Very easy.

removed the remnants of the old wheels and popped the new ones on....simple

Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!

Alighned the bracket and pushed in.

It would sometimes work, which led me to believe it was a switch. Looked on line and found the mail switch to go on was in the latch. I took it apart, 6 screws, wiggled the switch and it went on. So I found the door switch to be bad. It was very simple to change the switch.

Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.

Water leak solved...

After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.

Broken friction cable on the right hand side. Remove screws that hold dishwasher to cabinet, pull out the dishwasher far enough to get to the friction cable and rear spring. Remove broken cable. Attach new cable to rear spring and connect to door hinge. Push back dishwasher and screw in the two screws that keep the dishwasher attached to ... Read more the cabinet. Very simple.

I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.