CDBEH600SW2A Frigidaire Dishwasher - Instructions

I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.

Discovered upper wash arm had come off. It looked like it was repairable, but the bushing/clip holding the arm came off after one wash. Looked on line and reviewed part and saw it was a one piece assembly from photos. Removed old assembly by unscrewing from top of washer and screwed new assembly in place.

I installed the new spray arm without any tools and it worked perfectly.

First thing I did was turn off the power to the dishwasher, then remove the racks. Remove the foot plates, remove the two top screws holding the dishwasher. Then using the socket set, retract the two foot stands to pull the dishwasher forward. You may not have to do this step as I had to get it over tile. The pully springs are on the ... Read more sides, easily replaced. After replacing the springs and I recommend replacing both at the same time, put everything back. The hardest part will be the foot plates, there are two and getting them lined up and the screws back in is a bit of a challenge. Then you are done.

I removed the old spray arm by pulling it off of the base then I pushed the new one on and made sure it was on properly then I pit the base back into the dishwasher and it was good as new!

All I had to do was take out old racks and replace with new ones. However the top rack did require taking off the part where the water runs through, it was easy though.

I would like to comment on how quickly and efficiently the parts arrived. I placed my order on a monday morning and am pleased to report by tuesday afternoon t ... Read more hey arrived, much to my delight.

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.

Took no tools. Removed the melted pieces and snapped the new ones in the machine and I was ready to start washing!!! My wife and I are very impressed with prompt and courteous professionalism of PartSelect . I will recommend them highly. I would rate this a 5 star rating, wasn't able to change that star from one to 5

New one snaps into place easily.

Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings ( ... Read more ~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

Removed the clamp holding it to the floor and
removed the c-clips holding element underneath
and put new one in. Hard part was figuring out
what was holding the element but since I still
had the schematic drawing we figured it out.
Saved a bunch on a repairman. After watching
my friend install the new eleme ... Read more nt I could probably
do it myself next time.

This was really easy. Have done it before on other older dishwashers in the past.
Turned off the breaker for the dishwasher. Turned off the water supply valve. Unscrewed the screws in the panel that hides the parts under the dishwasher. Unscrewed the screws anchoring the dishwasher to the counter. Slid the dishwasher out about a foo ... Read more t. Inlet valve was located on the front left side of the dishwasher. Unclipped the wire harness. Placed a cookie sheet under the water line. Unscrewed the water line from the inlet valve. Unscrewed the two Phillips head screws holding the valve to the dishwasher frame. Got the new part. Put the screws back into the frame. Reconnected the water line and wire harness. Slid the washer back into place. Turned on the water valve. Watched for leaks. Turned the breaker back on and started the cycle. Watched for leaks. Once I saw there weren’t any replaced the screws anchoring it to the counter and replaced the cover on the bottom. That was it! Took me longer to type out the steps than it did to actually do the repair.

Grab the tab on the support and rotate 1/4 turn counter-clockwise to unlock it, then lift it off. The lower spray arm simply pops off the support by spreading two tabs underneath.

Align the opening in the lower spray arm support with the outlet post in the bottom and rotate 1/4 turn clockwise to lock.

*Note: directio ... Read more n to remove the filter basket differed from the manual. Visually line up the notches and do not twist too far when locking or you WILL break the retainer tabs.

Simply center the lower spray arm over the support and press down until it locks into place.