CDB350NW10B Frigidaire Dishwasher - Instructions

Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having th ... Read more e problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.

Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.

I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the t ... Read more hing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..

I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.

The hardest part was disconnecting the dishwasher. the motor is located on the bottom so after pulling it out and laying it down on the front of the machine the motor unplugs and 2 screws hold it in place.The new motor comes with "O" rings so I applied a little grease and put it back together. 2 minutes to replace motor, 15 minutes to dis ... Read more connect water and electric, 15 to reconnect.

Unscrewed retaining ring, replaced unit = piece of cake

It required no tools. It took less than one minute to connect the spray arm to the bottom of the unit. Our dishwasher is working perfectly now.

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa ... Read more sher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

It was simple, I do have extended warranty from AHS, but they charge me a trip charge of $55 per repair, and then all parts and labor is covered. But when I checked with Parts Select the parts costed me about $10, so I decided to do it myself.

While I was at it, I also bought other parts and updated my dishwasher with some upg ... Read more rades.

Good place to buy any parts from, they are very helpful, if you do not know your parts. They even had drawings of my dishwasher, and this actually helped me find what kind of other parts I could buy to upgrade my dishwasher.

Parts select is on my favorites list and pass it on to all my friends.

First, I had to remove a small metal paper clip that somehow ended up in the bottom of the dishwasher, which jammed the spray arm. The spray arm wasn't able to spin around, so it melted onto the heater. I removed the spray arm, and replaced it with the new one.

All I had to do was replace the spring and retainer on the side of the dishwasher which amounted to pulling it out far enough to reach the eyelet that the hook went into and then stretching it to the retainer attached on the other end. I really like partselect, I have done some things in the past and they are very helpful on the site and ... Read more on the phone and I would recommend them to anyone and I would not normally do that unless it has been an excellent experience.

simple repair..woke up one morning and after the dishwasher cycled, I noticed the upper spray arm laying on the top tray.
ordered new one from site, was delivered with-in 2 days ( with standard shipping) all 1 piece, took seriously 5 seconds to unscrew by hand and replace!

See posting under O rings. Get schematic Motor & Pump pg. 8 from pub # 5995487674. Steps: 1) run cycle so most water is pumped out of dishwasher 2) remove front cover to reduce weight of door; 3) disconnect electric plug, hot water hose [NOTE: be prepared for some water from hose], and waste tube all usually found under sink area; 4) remo ... Read more ve 2 screws at top of front panel; 5) lower leveling feet to allow best clearance; 6) put towels under front feet to protect floor and slide unit out from under counter; 7) place heavy blanket next to unit to protect floor and tip unit over on its side; 8) disconnect electric plug from motor and remove metal spring clip holding motor (2 torx screws) and pull clip off motor; 9)gently rock motor while lifting to remove from unit [NOTE position of motor for reassembly]; 10) put thin coat of silicon on O rings and place on new motor [look at old motor to make sure O rings are in proper slots; 11) line up motor and gently push new motor back into position; 12) reverse disassemble steps above. 13) run dishwasher through fastest cycle to check for leaks.

My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, ... Read more armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman

The Spray arm and the support had come off during operation and subsequently melted on the heating element. This was our fault, as a knife had slipped through the lower dish-rack and acted as a ramp to launch the spray arm as it came around. The support was a simple 1/4 turn counter-clockwise until it clicked into place, drop the strain ... Read more er basket into position around the support, them push the spray arm into place until the catches snap over the retaining ring molded into the support. All told, about 10 minutes, max.