- Home
- CDB1500AWZ
- Instructions
CDB1500AWZ Magic Chef Dishwasher - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door handle stopped engaging
4 of 5 people
found this instruction helpful.
-
Harold L. from winamac, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a lo
... Read more
ss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.
Read less
Was this helpful?
Thank you for voting!
Dishwasher leaked out of bottom
4 of 5 people
found this instruction helpful.
-
Phyllis from Grass Valley, CA
- Really Easy
- Less than 15 mins
I removed the old door seal -- it just slips right out. Then I inserted the new door seal. One thing I noticed on the old door seal and also in your photograph is that the last inch or two of the seal on both ends is kind of sliced in half perhaps to make it fit better in the corner. But we decided not to cut it yet and have been using it
... Read more
uncut as it arrived in the package. It is working great! No leaking! So we're not going to cut it. Thank you for offering this great service. It saved us a lot of money since we didn't call a repairman.
Read less
Was this helpful?
Thank you for voting!
Lower basket wheels fell off and were melted
3 of 3 people
found this instruction helpful.
-
Michael from Denver, CO
- Easy
- Less than 15 mins
Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer
Was this helpful?
Thank you for voting!
The dishwasher door would fall open
3 of 3 people
found this instruction helpful.
-
Michael from WEST NEWTON, PA
- Very Easy
- 15 - 30 mins
-
Screw drivers
I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and
... Read more
replaced the screws. The whole job took about 20 minutes. It was a very easy job.
Read less
Was this helpful?
Thank you for voting!
New house came with dishwasher, but had missing silverware baskets
4 of 6 people
found this instruction helpful.
-
Mark from Perry, OH
- Really Easy
- Less than 15 mins
Took the baskets out of the packaging and put them in the dishwasher, took about 15 seconds to put both in. They fit perfect, quality factory parts. Thanks PartSelect!
Was this helpful?
Thank you for voting!
Upper wash arm would not turn.
3 of 3 people
found this instruction helpful.
-
David from Fayetteville, GA
- Really Easy
- Less than 15 mins
Snapped the old part out and snapped the new part in.
It was a piece of cake.
It was a piece of cake.
Was this helpful?
Thank you for voting!
The dishes in the dishwasher weren't getting clean. I decided it would be cheaper to replace the clogged wash arm myself, before calling a repairman.
4 of 6 people
found this instruction helpful.
-
Georganne from Carolina Beach, NC
- Really Easy
- Less than 15 mins
First, I removed the screw, then I took off the old wash arm, then I replaced the wash arm, and replaced the screw. Nothing could be easier!
Other Parts Used:
Was this helpful?
Thank you for voting!
dishes not clean
4 of 6 people
found this instruction helpful.
-
David from Lake Zurich, IL
- Easy
- 1- 2 hours
-
Screw drivers
with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumul
... Read more
ator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.
Read less
Was this helpful?
Thank you for voting!
Soap not dispensing
3 of 3 people
found this instruction helpful.
-
Sue from SAN FRANCISCO, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.
Was this helpful?
Thank you for voting!
Dishwasher did not drain properly.
4 of 6 people
found this instruction helpful.
-
Phillip from Winter Haven, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I removed the washer from under cabinet.Turn unit on its side,removed hose connection,removed mounting screws,disconnect wire plug and removed drain pump.
I put a small amount of sealant on pump where it contacts the tub and reversed the process. Parts received in record time and in great shape.
I put a small amount of sealant on pump where it contacts the tub and reversed the process. Parts received in record time and in great shape.
Other Parts Used:
Was this helpful?
Thank you for voting!
Latch on soap dispenser door broke
4 of 6 people
found this instruction helpful.
-
Ronald from Longmont, CO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.
Was this helpful?
Thank you for voting!
The dishwasher got the dishes dirty not clean
4 of 6 people
found this instruction helpful.
-
Ken from Mapleton, UT
- Really Easy
- 15 - 30 mins
-
Screw drivers
My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together.
... Read more
The dishes are sparkling clean again!
Read less
Was this helpful?
Thank you for voting!
Dishawasher would not drain
3 of 3 people
found this instruction helpful.
-
Kevin from Dallas, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I removed screws in trim, kick panel and counter top. Turned off breaker at electric box, Dishwasher slid out easily. diconnected water line; so i could slide entire unit out of cabinet. Laid unit on side and cleaned up the water that leaked out.
Removed the pump with nutdriver, replaced pump and reconnected electric, drain hose and ... Read more screws.
Replaced unit into cabinet, connected water and turned on electric. no leaks, ran machine in rinse cycle, at time for pump I could hear and feel it was running, but no water. Evidently my original problem was the "air gap" device. I repaced it $4 at Home Depot and it works like a champ.
In hind site, the air gap probably ruined the old pump, so you might want to consider changing it out whenever you change the pump.
Removed the pump with nutdriver, replaced pump and reconnected electric, drain hose and ... Read more screws.
Replaced unit into cabinet, connected water and turned on electric. no leaks, ran machine in rinse cycle, at time for pump I could hear and feel it was running, but no water. Evidently my original problem was the "air gap" device. I repaced it $4 at Home Depot and it works like a champ.
In hind site, the air gap probably ruined the old pump, so you might want to consider changing it out whenever you change the pump.
Read less
Was this helpful?
Thank you for voting!
Dishes not clean, soap film on dishes
3 of 3 people
found this instruction helpful.
-
Joseph from Warren, NJ
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Impeller bolts to plastic chopper mount which is screwed to the top of the motor. Threads on chopper mount were stripped causing impeller to not spin fast enough (replacement mount, which is part of the chopper kit, is metal). Installtion was not difficult.
You have to reach underneath the washer and wedge a screwdriver on top of th ... Read more e motor to hold the shaft from moving.
You have to reach underneath the washer and wedge a screwdriver on top of th ... Read more e motor to hold the shaft from moving.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dishes were coming out dirty... cloudy and white.
4 of 7 people
found this instruction helpful.
-
Loretta from Ancram, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
I know that I have very hard water, but am reluctant to get a softener. I hope that changing the "guts" of the water delivery to my dishwasher will help...already replaced the filters which helped too... so far, it's a little better.
Installation was a breeze. Took off the upper, middle and lower spray arms. Had to loosen sc ... Read more rews in filter assembly to remove old manifold. Popped everything into place... had to scrape mineral deposits off clips that support manifold and upper spray arms.
Easy...
Installation was a breeze. Took off the upper, middle and lower spray arms. Had to loosen sc ... Read more rews in filter assembly to remove old manifold. Popped everything into place... had to scrape mineral deposits off clips that support manifold and upper spray arms.
Easy...
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!