CCV17RFLW1 Crosley Freezer - Instructions

Our repair was easy. No tools required. It was just popping it into place. I would like to say that we ordered our part and paid for regular dhipping and we recieved it the very next day! What great service! Thanks so much!!!

Two of my refrigerator door bins were broken and I had been using duct tape to hold them in place. I decided to look them up on PartSelect and was able to find exactly what I needed at a great cost. I ordered them and they came right away. I put them on the door needing no tooks and bingo, just like new! Imagine my heartache when ... Read more one somehow broke. Well I contacted PartSelect and they sent me another one at no charge and in less than a week!!!

snapped in new bin

I took the new part out of the box and snapped it into place, then I opened a bottle of champagne and celebrated.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Just snapped the piece in place. Fixed in less than 1 minute. The Lady on the phone was helpful in making sure I was selecting the right piece. Delivery was made in 2 days. I can't be more pleased. cw

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.

Found voltage coming into unit but not making it through the control unit. Thermo switch could easly be bypassed with no results so only thing left was the control mod. It was worth the $51.00 guess , ordered the part with credit card about noon, the next day Fed Ex came to the door about 2 PM the freezer was running by 2:30. Very impress ... Read more ed by everyone envolved. Spent the rest of the day bragging about my repair ability. Felt good to hear that baby fire up. Thanks again

replaced control board and installed surge protector

I paid about $50 for a tech to come to the house to troubleshoot the freezer. He id'd the temp control unit in about 30 minutes and told me he could repair the freezer for an additional $300 or so. I told him 'no'. I looked up the part number with partselect and ordered the temp control unit for about $40 including shipping. I simply plug ... Read more ged in the unit and reset the rear compartment panel and gaskets. I plugged the unit in. The freezer ran but did not freeze. I inspected the rear of the freezer and found that the tech had left the compressor unplugged. I connected the compressor and turned the freezer on, It is working just fine.

When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proc ... Read more eeded to instal motor and put refrigerator back together. It was simple.

Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut dri ... Read more ver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.

I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer ... Read more . Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.

Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.

Ordered new shelf an it came in two days. Snapped right on. Very pleased.