My Orders
CCE3450W Jenn-Air Cooktop - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The switch would not turn off the range. The switch just kept turning but nothing happened.
0 of 1 people
found this instruction helpful.
-
Jose from Victor, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I removed two screws that held the switch plate together. Then I removed two screws that held the faulty switch to the swtich plate. I then unpluged one wire at a time from the old switch and pluged it into the new switch. Reattached the switch to the switch plate and then reattached the switch plate to the stovetop. Bingo! Everything wor
... Read more
ked beautifully. It was so easy and I saved ~ $100.00 by doing it myself, as opposed to a quote that I got from a local repairman.
Read less
Was this helpful?
Thank you for voting!
bad surface burner switch
0 of 1 people
found this instruction helpful.
-
Lawrence from Birmingham, AL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release t ... Read more op edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release t ... Read more op edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.
Read less
Was this helpful?
Thank you for voting!
control switch was no good
0 of 1 people
found this instruction helpful.
-
Valentine from Bow, NH
- Really Easy
- Less than 15 mins
-
Screw drivers
I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.
Was this helpful?
Thank you for voting!
electric element would not function
0 of 1 people
found this instruction helpful.
-
david from castle rock, CO
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
2 screws to remove
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
Was this helpful?
Thank you for voting!
Sparks shot out from under knob, then, no surprise, the burner didn't work
0 of 1 people
found this instruction helpful.
-
Charles from Bourbon, MO
- Easy
- Less than 15 mins
I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch. ... Read more r />Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch. ... Read more r />Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Read less
Was this helpful?
Thank you for voting!
Infinite Rotary Control Failed
0 of 1 people
found this instruction helpful.
-
George from Centreville, VA
- Easy
- Less than 15 mins
-
Screw drivers
Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disco
... Read more
nnected all the wires at once.
gc.
gc.
Read less
Was this helpful?
Thank you for voting!
could not adj. temp. stayed high all the time
0 of 1 people
found this instruction helpful.
-
Don from CARROLLTON, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
replaced stove top switch
Was this helpful?
Thank you for voting!
Electric barbecue element not heating
0 of 1 people
found this instruction helpful.
-
S.. J. from Punta Gorda, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1. Diagnosed problem = switch at fault not element
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figu ... Read more ring out and solving the problem. Two thumbs up!
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figu ... Read more ring out and solving the problem. Two thumbs up!
Read less
Was this helpful?
Thank you for voting!
back burn would turn high no mater where you set the control knob.
0 of 1 people
found this instruction helpful.
-
William from Valley Grande, AL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I
... Read more
figure I saved about 100.00 dollers plus I learned something.
Read less
Was this helpful?
Thank you for voting!
one of the four burners was not working
0 of 1 people
found this instruction helpful.
-
Amy from Rosebush, MI
- Easy
- 15 - 30 mins
-
Screw drivers
Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!
Was this helpful?
Thank you for voting!
Bad burnes off on switch
0 of 2 people
found this instruction helpful.
-
Jim from Two Rivers, WI
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Easy as Pie.
Was this helpful?
Thank you for voting!
Front right burner did not turn on
0 of 2 people
found this instruction helpful.
-
Vanna from St. Johnsbury, VT
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
We followed the instructions on the video after receiving our part - they were perfect instructions and led us right through the repair. I have to say it would have been harder to do with one person - but probably doable.
Was this helpful?
Thank you for voting!
Burner only operated on high, no medium or low heat.
0 of 3 people
found this instruction helpful.
-
Paul from Collegeville, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pul ... Read more led the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pul ... Read more led the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
Read less
Was this helpful?
Thank you for voting!
surface burner failure
-
Gerald from Hot Springs Village, AR
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.
Was this helpful?
Thank you for voting!
Burner was very hot regardless of setting
-
David from Woodland Park, CO
- Really Easy
- 15 - 30 mins
-
Screw drivers
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.
Was this helpful?
Thank you for voting!