CAM2742TQ2 Whirlpool Washer - Instructions

The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.

I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to ... Read more see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]

Watching videos identified what parts to purchase.
Once identified - WATCH EACH PARTS VIDEO (again).
Lessons learned:
1) better to NOT tilt the washer
2) watch (more than once) and learn from the videos
3) must difficult step was loosening the tub retaining nut without having a spanner wrench (used a hammer and a ... Read more short / wide blade screwdriver)
4) ended up being the tub support was not sitting properly in the suspension plate
5) cleaned and changed parts while apart
6) running as good as new

Thanks!!

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

On this model, no need to tip washer on back. Tilt console back and disconnect lid switch. Remove two clips holding back to top of washer (under console). Then remove top and front as directed in the video. The pump is accessible from the front of the unit, just below the tub. Hose clamps are easy to remove/replace. Took more time to ... Read more wipe inside of washer clean than to remove/replace the water pump. Total time was just over 30 minutes.

Removed old tube and replaced with new version. Replacement slightly different than original since the new part included a feature that appears to prevent the problem. New part still fit and is operating well so far.

Replaced the springs after watching the video's from this site and problem has been solved.

1. Watch a video on installation, there are many on the internet.
(unplug the washer)
2. remove the screws on the back of the control panel to lift the control panel out of the way.
3. use a flat head screwdriver to remove the clips that hold the cabinet to the back panel.
4. disconnect the lid switch from the control ... Read more panel by removing the clip that connects them at the top of the cabinet.
5. tilt the cabinet forward to remove it.
6. use a flat head screw driver to remove the two clips that hold the water pump to the motor and swing the water pump out of the way.
7. use a nut driver to remove the shipping screw that holds the clips on to the motor.
8. disconnect the wiring harness from the motor
9. remove the two clips from the motor with a flat head screwdriver and remove the motor
remove the three prong coupler and rubber gasket from the old motor and put them on the shaft of the new motor
10. remove the 4 rubber pads from the old motor and slide them onto the new motor.
11. insert the new motor into the washer aligning the prongs of the coupler.
12 reassemble the washer in reverse order of disassembly
(the shipping screw does not need to be reinserted into the spring clip that holds the motor)

The "O" ring just snaps in place. For the lid it was necessary to remove the screws from the hinge on the left side, then extract the hinge rod. Once the hinge rod was removed the lid lifts out. Removed the hinge rod from the right side and installed it on the new lid. Then put the lid back in place, insert the hinge rod into the left sid ... Read more e of the lid and replace the screws. Removed the safty switch actuater from the old lid and snapped it in place on the new lid. Done !

I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago

First I removed the fabric softener cup then the cover with seal. I then used an 11mm socket to remove the bolt, pulled up on the agitator cam removed the old gears and replaced with new ones. Put it all back together and it Works great