C3521WRV Magic Chef Range - Instructions

I can't believe how easy this was to fix! I amazingly found the part on-line at PartSelect website. I love that you pick part by size, color, etc. I didn't have a part or model number, so this made it super easy! I ordered the part and got it in the mail within 2 days....YEAH! I got my screwdriver out and attached the peice, slid the ... Read more drawer back in and shazam! it was fixed! Thank you PartSelect and kudos to the person that set up the way you order your parts......awesome! Thanks!

My husband removed the screws holding the damaged element and removed it before the new one arrived. When we received the replacement part, it took only about 10 minutes for him to repair the oven, inserting the new element.

First I removed the two screws that hold the element in place. I then pulled the element out about three inches and disconnected the two wires, being careful not to pull the plugs off. I then inserted the new element and reattached holders. It was very easy and took less than five minutes. The part arrived amazingly quickly. The stove wor ... Read more ks great now.

Broken part was already removed, so I used the screw from the broken support and installed the new support. Very simple, easy, and painless.

the new elements were super easy to replace. the old ones just pulled out and the new ones easily pushed in. the top one was a little more difficult only because it had brackets that had to be slid of and then slid onto the new one.

removed drawer from track replaced supports on track and one on the drawer.

Called repairman, he never called back for a week. Gave up and found your website, ordered the part. You said it would take 3-5 business days. You lied, it was there the next day. Taking old element out starts with shutting off the juice. Remove trays, pans, etc. Unscrew two screws, pull out elements ends, unclip from wires, reverse ... Read more the process with new one. You need a light to do this.

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires reverse the order to install the socet was easy but after i was done discovered that the base of the old bulb was stuck in the socet keeped it for future use

I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the ... Read more stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh ... Read more t bulb in was not the problem.

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short t ... Read more ime to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

Pretty simple, except the element melted very close to one end, so the screw holding the element to the rear of the stove was partly melted also. Had to drill it out & used a nut & bolt to secure the new element.
Apart from that, it was a breeze. As others have done, I re-tightened the lugs that the element plugged into.
Suggest ... Read more a "test heating" before using stove: mine had a strong odor on first use, fine afterwards

replaced burner element

Turned off the breaker to the stove. Removed the screws holding the old parts in and unplugged the element. After reshaping the element because it got damaged in shipping I plugged the wires to the new element, replaced the screws and turned the breaker back on. Tried the stove and it has worked fine since.