C236NGB Jenn-Air Cooktop - Parts

The function of the grease filter is to trap grease into the filter from the exhaust air. The grease filter is intended to be used with certain downdraft cooktops and ranges. This grease filter is roughly fourteen inches long and almost twelve inches wide, and chrome in color. Removing your old grease filter and replacing it with a new on...Read moree is an easy job, users say it took them less than fifteen minutes to install. We recommend that when removing your current grease filter, you use work gloves to protect your hands and clean the entire area thoroughly before installing the new filter.

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

This screw is sold individually.

The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the left or right hand side of your oven, and is approximately 20 1/2 inches long. If your oven door will not open or close easily, you may need to replace this part. It may be a good idea to repl...Read moreace both hinges at the same time. If a spring has become loose on one hinge, the other hinge is likely to have the same issue. The repair is simple and only requires a Phillips screwdriver and a small bent nail. For a full step-by-step guide, check out the video below.

This surface burner switch, also known as an infinite switch, controls and regulates the heat output of the burners on a stovetop. The user simply adjusts the knob on the user interface panel, which in turn controls this switch. Made for various ranges, wall ovens and cooktops, this is a genuine OEM part that comes by itself, without any ...Read morehardware like screws or nuts. This burner switch is an electrical component that you also handle directly, so it can become faulty leading to problems like your stovetop not heating enough, overheating or staying at a fixed heat. This burner switch is a vital component for your stovetop and if it presents any of those issues, it needs to be replaced immediately. A screwdriver, set of pliers and wiring diagram will be needed for the replacement and installation process, and you will need to remove your appliance from the wall outlet first. Remove the knobs from the control panel and then gain access to the underneath portion of it with your screwdriver and disconnect the switch. Remove the wires from the burner switch with a set of pliers and disconnect the securing screws holding the switch in place. Now, you can install the new switch and reassemble the panel, being mindful of wiring each connector to the appropriate wire.

This down-draft fan switch kit comes with the switch itself and two metallic push nuts. At 125 volts,this switch will allow for 6 amps, and at 250 volts, this switch will allow for 250 volts. This switch runs at 1/4 horsepower.

This genuine surface burner control knob allows precise adjustment of cooktop heat levels, giving users control over burner output from low simmer settings to high-heat cooking. Constructed from durable plastic, the knob features clear temperature markings and a highly visible indicator line for easy operation and accurate setting selecti...Read moreon. Replacing a cracked, worn, loose, or missing knob can help restore proper burner control and maintain the appliance's original appearance. Installation is quick and tool-free—simply pull the existing knob straight off the control shaft and press the replacement knob firmly into place until fully seated. The knob measures approximately 1.5 to 2 inches in diameter and features a black finish with contrasting control markings for enhanced visibility and everyday convenience.

This jar is a little over five inches long. It is made of glass and is used for collecting the grease drippings of gas ranges.

This cartridge receptacle is almost four inches long. It is white in color and is made of ceramic.

This motor isolator is less than an inch long.

This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to ...Read morewear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.

This grease jar lid is used for some of Maytag/Jenn-Air's brands of ranges and cooktops. This lid is not quite an inch high and is three inches in diameter.