BTF2140ES3 Crosley Washer - Instructions

Replaced pump, by removing back panel and removing the two screws holding the pump to the bottom of the machine. The only difficult aspect was dealing with the hose clamps, these were extremely awkward to work with in a confined space. The repair would have been less than 30 min if the hose clamps weren't so difficult to put back in place ... Read more .

Removed top cover of washer to get to the door lock mechanism then used a phillips head screwdriver to remove door lock mechanism. I then replaced door lock mechanism with the new one I bought from PartsSelect. The repair job was very easy and took a total of 15 minutes to remove old part and install new one.

First called a repairman.Wanted over $300 to put a new door lock assembly in.Searched the web, found PartsSelect,bought part for less than $75,husband did repair in less than 30 min.
VERY happpy customer.

THANKS

Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no ma ... Read more tter what else you fix, this will break and kill it at some point. Piece of crap!

Close examination revealed cracked plastic inlet area. I removed top of machine any carefully was able to loosen an pull damaged (froze over the winter) part back to remove. Attachment screws difficult to access, had to use magnetic screwdriver attachment during reassembly. Always iffy when working with plastic parts.
Part arrived ... Read more 2 days later, took about 40 minutes to install.

unscrewed the old handle, and screwed the new one on. It only took 2 minutes to fix. Very easy!!

2 screws and about 48 seconds of work. very easy.

door not level son slammed shut and door strike broke

Like another commenter, my teenage daughter ripped the handle off at the top in a huff. My husband simply unscrewed the broken handle and replaced it with the new one. We now make sure to open the door from the middle of the handle, not the top.

No spin, water+drain worked playing with settings. Dart 1-door switch. Got code-tested motor-ok. Replaced motor control board

E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.

First I removed the "wire" and spring that hold in the rubber seal at the door.

Then I removed the 2 screws that hold the door loc ... Read more k in place.

Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.

Runs fine now.

Very easy. Remove 2 screws from the inside of the door. Take out the broken pieces and screw in the new one using the old screws.

Found that the fill valve was leaking and clothes would be wet if not removed right away.
Removed 2 screws from back of top panel and removed panel.
Disconneced water lines and two screws held valve assembley to detergent dispenser and unplug wires from the 3 solenoids

I heard that the repair job was simple and the part was not expensive (whew!) The repair video on your website was MOST helpful and gave me confidence. At first I tried it exactly as the guy demonstrated and all went well removing the broken support. Installing the new one (on the right side) was impossible for me. I could not get good ... Read more enough leverage to fully re-insert the lock pins and I was slicing up my arm on the sharp metal edges. I removed the 900+ screws (just kidding- but there were quite a few) from the back panel and could access the lock pins MUCH easier. All four for both shock absorbers snapped right in. Re-attaching the rubber vent hose involved a few cuss words but I got it back on correctly after taking a break. All is great with the little washing machine once again! Thank you for the installation video and amazingly fast shipping, wow.

screwed in the new legs and leveled it off again.