BC30 (RY30004A) Ryobi Brush Cutter - Parts

The Fuel Tank is an OEM replacement part. It is compatible with the models shown below. It includes the fuel lines, fuel cap and fuel filter. If you need to order the fuel tank bumpers, they are sold individually as part number 98792.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

Genuine OEM replacement part, this part is sold individually. This part is where the stringhead assembly is mounted on the Trimmers shown below. It attaches to the spindle. The thread mount on the spindle is a left hand thread.

This is a genuine OEM replacement part, it is sold individually. The purpose of the 900994004 Carburetor Gasket is to prevent an air leak, which would cause the engine to run poorly. It is advised to replace these gaskets when replacing or repairing the carburetor.

This crankcase cover gasket seals the crankcase cover of your lawn equipment engine, preventing air or fuel leaks and maintaining proper internal pressure. It is sized at 2 1/2 inches by 2 1/2 inches and is commonly found where the crankcase cover attaches to the engine block. You can tell if a crankcase cover gasket is broken if there is...Read more oil around the edges of the cover. Your machine may also experience a loss of power or unusual noise. If the gasket is not replaced, your machine may have fuel leaks or decreased performance. Debris and contaminants will also enter the engine, reducing the lifespan of your machine. When replacing the gasket, use a wrench or socket to unthread any bolts securing the crankcase cover. You will then be able to take the gasket off your machine. Bear in mind that this OEM gasket is sold individually.

Genuine OEM replacement part designed for use with string trimmers. It is the part of the trimmer that contains the cutting line. It is made out of plastic and it is sold individually. Please note the spool housing and the cap are both sold separately. When replacing this item no tools are needed. • Install the string head assembly on...Read moreto the gear head shaft by turning counterclockwise • Tighten the string head assembly securely

Genuine OEM replacement part, this item is sold individually. This Clutch Drum is used on all of the outdoor products shown below. It contains the screw to attach this part to the spindle of the engine. It is usually a Torx T-25 Screw or a T-20. Once the engine gets to a certain RPM the clutch will expand and come in contact with the inside of the clutch drum. This will start the rotation of the Trimmer drive shafts.

The air filter in your trimmer keeps the engine running smoothly. It filters out dirt and debris from the air before it enters the engine, ensuring that clean air is used for efficient fuel combustion. This helps protect the engine and maintain its performance. If the air filter is clogged or damaged, it should be replaced to avoid reduce...Read mored engine performance, increased fuel consumption, and potential engine damage. To remove the existing filter, consult your user guide to locate the air filter housing. Depress the locking tab on the housing cover, lift it off, and remove the filter. Follow any specific installation instructions for your machine model. Please note that this OEM air filter is sold individually.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.