BAD1 Frigidaire Dishwasher - Instructions

Make sure power is off. Remove metal toe kick with fillips screw driver. Reach under dishwasher with 1/2" open
end wrench and completly unscrew brass nuts from element ends. Then open door and pull element ends straight up. Note: As you pull element ends up (inside washer) you are also forcing the element end wire connectors to come ... Read more off underneath. The electricial connectors are very hard to get off any other way.

Wendell Hensley
Madiso0nville, Tn

I had to remove the dishwasher from under the counter. I then had to unscrew (from the bottom) the bolts that held the heater in place. After that I ran into a problem of disconnecting the wires that ran to the heater. I did not want to "force" the wires off and I was unsure how exactly to remove them. I figured out that they are real ... Read more ly hard to pull off but there are no clips holding them on, so you won't break anything off. Once I got the wires off, I was able to screw the nuts onto the new heater and put it back into place.

Only took me 5 sec, just push it in. Good as new. Thanks for the fast deliver .

All I had to do was take out old racks and replace with new ones. However the top rack did require taking off the part where the water runs through, it was easy though.

I would like to comment on how quickly and efficiently the parts arrived. I placed my order on a monday morning and am pleased to report by tuesday afternoon t ... Read more hey arrived, much to my delight.

Place spray arm into receptacle. Take nut and screw on being careful not to over tighten. This will strip the spray arm and the same problem will occur. Easy fix!

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

Pulled the broken one off, snapped the new one on.

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.

Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings ( ... Read more ~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

First I disconnected the dishwasher, then I disconnected the drain hose. I pulled the machine from under the counter and turned it on its side, so that I could see where the drain pump was. I removed the two screws that hold the element in place. I then pulled the pump out and disconnected the two wires. I took a good look where each wire ... Read more was attached. I also had to disconnect the pump from two small hoses. I installed the new pump, I had ordered from PartSelect, following the reverse procedure. I reconnected the dishwasher and slided back under the counter. I confess I didn't believe it would work. I was prepared for failure. The machine started, then when the cycle changed, I heard the water draining into the waist pipe under the sink. New hot water filled the machine. Would this water be drained out and at the end, after the rinsing cycle, would the dishwasher be empty and completely free of water? I waited for the end of the rinsing, then I opened the door and checked for any water left at the bottom. Suddenly a feeling of joy and pride went through me. All water had been drained out by the new pump. I had repaired my dishwasher. I didn't have to throw this handsome and well made machine into the street. My kitchen sink was no longer full of glasses and dishes. I was washing all I had accumulated during the week. My kitchen became clean and organized just like before. At this point I took an oath: when my dishwasher would break down next time, I would repair it , even if its motor, the most expensive part, had to be replaced. I was going to do it with the help of the experts at PartSelect. Thanks guys for your help and for inspiring confidence in myself. I DID IT! What a great feeling!
Now I understand the feeling a doctor must experience when he brings back to life a dying patient.

New one snaps into place easily.

Turned off power to dishwasher.Used a screw driver to rermoved the outer top of door.Used star wrench to remove door latch.Repalced wire for wire on door latch.Reinstalled door latch with star wrench.Reinstalled outer top of door with screw driver.Turned power on.Tryed door lath.Operation is Ok.Ran dish washer.No leaks.Operation is OK.

Removed 6 screws, pulled the front cover forward, removed the old door latch, installed the new latch, replaced the screws, DONE! Took about 10 minutes. The new door latch works to open and close the door, and the dishwasher runs fine when the door is closed. However, the new door latch does not lock the door into place like the old on ... Read more e did. I didn't remove the screws and loor latch assembly again, but there must be a difference between the old part or the new part. And I noticed that the old part number and the part number of the replacement part are not the same, although the website indicated that it was the correct part for my model.

took it out of the bag and snapped it in. Less than 10 seconds.

Our dishwasher sat in a warehouse for a year after our move from CA to TX. When I finally installed it, there was some sort of white mineral deposit that had built up on the heater element. I didn't notice it back in CA. I tried to get as much as possible off but it kept building. So I purchased a new heater element. It's been in for a fe ... Read more w weeks and my wife thinks the build up is happening again.
To Repair;
Unscrew the dishwasher from the counter. They'll be one or two screws attaching the dishwasher on the underside of the counter.
Pull the washer out carefully.
Remove any dishes and the bottom rack.
Tilt washer on it's side.
Remove wire connections to heater element (They slide right off but make sure to remember which one goes where)
Unscrew the nuts that are holding the element on. I used some pliers. It wasn't difficult.
Remove old element and replace with new.
Reverse order.