B1ESN1601B (01) Bosch Dishwasher - Parts

This wheel is a dishwasher rack wheel designed for the upper rack of your appliance. The roller wheel is approximately 1.25 inches in diameters and includes the brushing you need for installation. It simply clips right on to the rack frame. After the wheel are attached to the side of the dishrack and are placed into the slides on either s...Read moreide of the appliance. Dishrack roller wheels allow the upper rack in a dishwasher to glide in and out of the appliance with ease. Due to the fact the roller wheel is made of plastic they tend to wear out after a period of time, also they can break. We do recommend you replace these rack wheels in pairs as they often wear out at the same rate. These wheels are sold individually.

This dishrack wheel is designed for use on the lower rack of your dishwasher, it allows the rack to roll in and out of your appliance with ease. This roller wheel includes the locking clip required for installation. The roller wheel attaches directly to the rack, you simply snap it into place on the frame of the rack, it does not include ...Read morethe axel. Due to how the roller wheels wear out we recommend replacing them in pairs. The diameter of the wheel is approximately one and a half inches. The roller wheel and clip are made of plastic.

This door seal, also known as a door gasket, is an authentic manufacturer replacement part for your dishwasher. It is responsible for creating a watertight seal between the tub and dishwasher door and preventing water from leaking out while the dishwasher is running. Therefore, if you notice water leaking from the front of your dishwasher...Read more and difficulties closing the door, then it is likely that the seal is either worn down, torn, or has a buildup of mold. Carefully pull the defective seal from the perimeter of the tub and clean the area thoroughly. Place the new seal in the grooves around the tub and close the dishwasher door to press it into place.

A holder is used in dishwashers, it is known as the dishrack stop kit. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack slides on. These stops help keep the rack on the rail, without this part the upper rack of your dishwasher will not slide in and out of your d...Read moreishwasher properly. If you need to fix both the left and right rail you will need to order two kits. To install this part, you will need to remove the upper rack from your dishwasher, and you may need a flathead screwdriver. These front and rear rack stops are made of plastic and they are gray in color.

This drain hose is designed for use in dishwashers. After the wash cycle is complete the water need to leave the dishwasher, this drain hose it carries the dirty water from the drain pump to the kitchen sink drain. Because this part is made of plastic it can be damaged, which means you will need to check this part if you notice any leaks ...Read morecoming from your appliance. This hose is approximately five feet long, and it includes one o-ring. Before you begin repairing your dishwasher you need to unplug the appliance and shutoff the water supply.

This check valve is a genuine OEM part that is compatible with several different makes and models of dishwasher. A check valve is designed to prevent the backflow of dirty water, food waste, and debris back into the dishwasher by sealing the valve of your dishwasher when the dirty water exits. In doing so, it also protects the pipes and p...Read moreump system from any potential damage that backward-flowing water could do. If your dishwasher is experiencing issues with filling, draining, or cleaning properly, the check valve may need a crucial replacement. This check valve is made of translucent plastic, is found near the drain hose and drain pump assembly, and measures approximately 1-inch by 1.5-inches.

This door hinge lever bearing is for dishwashers. Door hinge lever bearing allows the door hinge lever to move smoothly.

This float switch is a replacement sensing component designed to detect water levels and prevent overflow conditions. It helps regulate operation safely and is commonly replaced when switches stick, fail to activate, or provide inaccurate readings.