Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer drawer light switch failure.
2 of 3 peoplefound this instruction helpful.
HARRY from FSTRVL TRVOSE, PA
Really Easy
Less than 15 mins
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into
... Read moretrim. Plug refrigerator into wall socket.
Read less
Was this helpful?
Thank you for voting!
ice despencer not running
2 of 3 peoplefound this instruction helpful.
Joseph from Whiting, IN
Really Easy
15 - 30 mins
Pliers, Screw drivers
repair&parts instalation was easy but troubleshutting difficult.
Was this helpful?
Thank you for voting!
Ice Maker couldn't drop ice through the door.
2 of 3 peoplefound this instruction helpful.
Linda from Richmond, VA
Really Easy
15 - 30 mins
I pulled the drive ring off of the icemaker and replaced it with the new part. Saved a $150 service call plus cost of part. It cost me a little over $11.00 and a repairman probably would have charged $30.
Was this helpful?
Thank you for voting!
Door started to sag causing it not to close correctly
2 of 3 peoplefound this instruction helpful.
Jason from Colorado Springs, CO
Really Easy
15 - 30 mins
Socket set
Took door off refrigerator and removed worn parts and replaced the aforementioned parts, which took only a few minutes.
I followed the video of your repair man. Made it very easy.Thanks.
Was this helpful?
Thank you for voting!
No problems
1 personfound this instruction helpful.
Richard from PORT JERVIS, NY
Very Easy
Less than 15 mins
Just plugged it in
Was this helpful?
Thank you for voting!
Soring old, need replaced. Air leaking in and melting ice
1 personfound this instruction helpful.
Jerlene from BERLIN, MD
Very Easy
15 - 30 mins
Nutdriver, Pliers
Followed included instructions. Thank you.
Was this helpful?
Thank you for voting!
the auger had broke out the plastic of the ice enclosure
1 personfound this instruction helpful.
Tommy from PHENIX CITY, AL
Very Easy
15 - 30 mins
Pliers, Screw drivers
Removed the ice bucket, reached under the ice enclosure and unplugged the auger motor removed the ice enclosure, attached the auger motor on the new ice enclosure reinstalled the new ice enclosure, plugged the auger motor and put the ice bucket back in place. The hardest part was to get the forked piece that goes inside the ice enclosure
... Read moreoff of the auger motor. I ordered the part one day and it was at my house the next day!
Popped out the old switch and replaced it with the one dying
Was this helpful?
Thank you for voting!
Ice bin drive ring broke
1 personfound this instruction helpful.
Boyd from North Fork, CA
Really Easy
Less than 15 mins
Screw drivers
Removed the screws that held the main ice bin and slid back the bin to leave space behind the auger to remove the broken ring. Replaced with new ring and replaced screws to hold ice bin back in place.
Was this helpful?
Thank you for voting!
Ice flap in door was unintentionally broken due to ice jamb.
2 of 4 peoplefound this instruction helpful.
George from New Port Richey, FL
Easy
15 - 30 mins
Screw drivers
Removed approx. 5 phillips screws to access the flap from the outside of the freezer door and R & R'd the flap, then repaced the screws. Fairly simple installation. Most impressive was how easy it was to find the part here and the quick delivery.
Was this helpful?
Thank you for voting!
Drive ring disintegrated
1 personfound this instruction helpful.
Joe from GRANTSVILLE, MD
Easy
15 - 30 mins
Removed all screws on back and 4 on front. That part is easy IF you have a Torx of the right size. Slip out the ice bin a bit and replace the drive ring. Reassembly is a bit harder since some internal shift can occur -- rotate or tilt the whole assembly to get two -- I think -- screws started. No need to over tighten screws; snug is good
... Read moreenough.
Read less
Was this helpful?
Thank you for voting!
Ice door broke and would not let Ice out of ice maker
2 of 4 peoplefound this instruction helpful.
Charles from Gonzales, LA
Easy
15 - 30 mins
Screw drivers
First remove srews from front icewater panel Second pushed panel up to remove and disconect electric conection. Third rmoved broke ice door and installed new one in holder frame. Fourth reversed steps two and one. Job cpompleted.
My Orders
