My Orders
AW300C2D Kelvinator Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
water filling in machine without turning on
1 person
found this instruction helpful.
-
Christine from DALLAS, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Grann
... Read more
y rocks!
Read less
Was this helpful?
Thank you for voting!
water not coming into machine fast.
1 person
found this instruction helpful.
-
Donna from Oxford, MA
- Really Easy
- 30 - 60 mins
we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing
Was this helpful?
Thank you for voting!
Washer would only let cold water in,then not fully cycle
1 person
found this instruction helpful.
-
George from Ketchikan, AK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.
Was this helpful?
Thank you for voting!
leaking
1 of 2 people
found this instruction helpful.
-
Wing from Oakland, CA
- Easy
- 1- 2 hours
-
Screw drivers
Just took out the old one, replace the new one and clip it.
Was this helpful?
Thank you for voting!
Hot water was not entering the machine, but cold water flowed smoothly
1 of 2 people
found this instruction helpful.
-
Ronald from Saint Louis, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finis ... Read more hed!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finis ... Read more hed!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.
Read less
Was this helpful?
Thank you for voting!
water over flowing, old valve stuck open.
1 of 2 people
found this instruction helpful.
-
william from mayfield, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.
Thanks PartSelect.
Was this helpful?
Thank you for voting!
hot water kept filling the tank
1 of 2 people
found this instruction helpful.
-
Bob from Birdsboro, PA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNEC
... Read more
TED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL
Read less
Was this helpful?
Thank you for voting!
Cold water was filling slower than the hot water.
0 of 1 people
found this instruction helpful.
-
Steve from Fort Mohave, AZ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pulled out the machine. Disconnected water lines. Removed four screws attaching the top brackets. In rear of top panel. Slid top panel forward and clear of valve. Removed two wire harnesses. Removed two screws holding valve to the back panel. Pulled valve down and out. Removed outlet side line spring clamp with channel lock pliers and pul
... Read more
led hose off old valve. Installed outlet side hose and spring clamp onto new valve. Placed valve up into place and installed two screws. Installed two wiring harnesses. Replaced top lid. Replaced lid bracket screws. Re-attached water hoses and pushed the machine back into place.
Read less
Was this helpful?
Thank you for voting!
No cold water supply
0 of 1 people
found this instruction helpful.
-
Harold from Kansas City, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed two screws that held top of washer in place. removed top of washer. Removed two screws that held water inlet alve in place. Removed clamp and outlet hose from old inlet valve.
... Read more r />
Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.
... Read more r />
Removed two screws hold wash machine cover in place. Removed cover. Unscrewed cold and hot water supply lines from old inlet valve. Removed two screws holding inlet valve in place. Removed clamp and hose from inlet outlet hose. Replaced inew inlet in reverse order.
Read less
Was this helpful?
Thank you for voting!
Front load washer continued to fill with water until door failed. Major Flood
0 of 2 people
found this instruction helpful.
-
Malcolm from Shelley, ID
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed screws at back securing top panel (4).
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so f ... Read more ar!
Removed screws holding water inlet valve to back of machine (2)
Removed water hoses to bucket
Removed squeeze clamp securing water distribution hose from inlet valve
Reversed method with new valve.
Very fast...~25 min
Works fine so f ... Read more ar!
Read less
Was this helpful?
Thank you for voting!
water not turning off
0 of 2 people
found this instruction helpful.
-
Anita from Orange, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this
... Read more
point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.
Read less
Was this helpful?
Thank you for voting!
No hot water in machine
0 of 2 people
found this instruction helpful.
-
julie from minneapolis, MN
- Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come o
... Read more
ff so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!
Read less
Was this helpful?
Thank you for voting!
Water would not shut off
0 of 2 people
found this instruction helpful.
-
Todd from Eagle River, WI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reve
... Read more
rse of removal.
Read less
Was this helpful?
Thank you for voting!
water would not shut off causing door to pop open and spill all over the floor
0 of 2 people
found this instruction helpful.
-
Joe from Interlaken, NY
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.
Was this helpful?
Thank you for voting!
water dripping into the tub when off
0 of 2 people
found this instruction helpful.
-
George from St. Louis, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the co
... Read more
ntrol panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!
Read less
Was this helpful?
Thank you for voting!