ATB19 Refrigerator - Instructions

remove back lower panel using nutdriver. Locate and remove Relay and Overload parts from side of Compressor which were located inside a small white box shaped cover unti held on by a spring clip. Attach new Relay and overload to 3 pin terminals on side of compressor. Attach 1 white & 1 orange/white wire to relay terminals. Attach supplied ... Read more white jumper wire to Overload and other end to Blue wire. Instal new cover supplied with kit replacing old box type cover.

Glass sheet came in perfect condition, just put back in refrigerator and has been fine ever since. Not the first time I had ever taken out to clean, but it will be the last. From now on, I clean it in the refrigerator.

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting po ... Read more wer in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

First of all, let me say that I'm a 50 year old single woman. If I can do this repair, anyone can! After unscrewing the back of the unit that houses the compressor, I found the relay overload switch which is attached to the compressor. I pulled the part off and discovered that it comes in one piece. The replacement part came in 3 piec ... Read more es. I intially thought they sent the wrong part. After a little thinking outside of the box, I figured out that the replacement part was indeed the correct part and that it comes in 3 pieces instead of one. It would have taken 5 minutes to repair if I had realized this early on. Once replaced, the refrigerator/freezer was cooling within 10 min. I sent the Run Capacitor back after telephoning a customer service rep. She was so courteous and helpful! What a fabulous company. I highly recommend. I saved myself approx. $250.00 doing it myself.

First I removed the 14.3 tons of freezer contents, closed the water valve, shut off the juice, and removed the freezer bins, the freezer door and the three screws that held the element in place. After bringing in 397 hand tools from my garage inventory, I loosened the unit and, after extensive evaluation, I finally disconnected the wiring ... Read more connector from its freezer rear wall connector counterpart. You ain't gonna believe the rest of my story--of total ineptitude by an experienced fix-it-yourself dummy.

I searched the internet for a replacement ice maker and found it at partselect.com. I called Sears to ask if I could add my refrigerator to my existing appliance repair account. Sears said sure--it would cost me only one arm, three toes and one grandchild. I abruptly declined their magnanimous offer—I don’t give up my arms and toes so easily.

I visited the local Maytag repair parts and service retailer, who advised they didn't do parts anymore. Expecting their repair price would be greater than Sears, I resorted to partselect.com. I called them to be assured what I was buying was not mistakenly a 747 Landing Gear. On the afternoon (West Coast) of 4/28/10, I ordered (via internet) one PS21215123 Ice Maker Assy. Much to my pleasant surprise, it arrived via FedEX on 4/30/10 (no freight charges to me).

My repair/replacement efforts were hampered by the effects of my right rotator cuff surgery a few months before and major left wrist surgery two months ago to remove fractured bones and torn ligaments.

Undaunted by my physical handicaps, I forged forward. After re-installing the unit, I turned the water supply and electricity back on. It was graveyard dead. I wisely then bought two bags of ice as an interim solution to the severe needs of my wife and me for our daily chilled evening cocktails. I removed the unit, checked it out and re-installed it. I bought two more bags of ice. All the while, I turned the water and electricity off and on as required by reasonable safety standards. High tediousness!

Several more home maintenance tasks then arose for Sergeant Super Fixer, but I returned to the ice maker problem on 4/8/10. Last chance--remove the device and insure there was no frozen ice in the inlet tube--or call the local partsless repairman. No ice found, but I did learn the wiring connector to the unit was awry--no contact! While explaining that to my wife, I realized the two upper mounting screws were intended to be partially installed into the freezer wall to accommodate the unit's slotted mounting holes! Then, tighten the screws. Oh my God! During my 143 installations and removals, I had installed those screws blindly--using the (handicapped) skills of my right and left hands without any benefit of direct eyesight.

I returned to my challenging project this morning (4/9/10), fully utilizing all the expertise I had gained yesterday. Fifteen minutes of amusing effort! Turn on the juice! Turn on the water!Two hours later, ice cubes were dropping into the bin like rhinoceros bisquits in the jungle.

Hallelujah! I now am free for the next challenge!

HINT: Put a bed pillow (an old one, or your wife's) in the freezer compartment to soften the harshness of its cold metal on your back, if you use the "crawl in on your back" approach.

Hubby and I were cleaning both fridges and I did not realize that the shelves holding the crisper drawers were not the same. The kitchen fridge shelf is all one piece (frame and glass), but the garage fridge shelf is not -- the glass just sits on the frame. I tilted it up vertically to rinse it off in the kitchen sink and CRASH, the shelf ... Read more fell out and broke everywhere. We found glass bits for weeks. Anyway, I went online to find a replacement shelf, found PartSelect (best online price) and ordered. I broke the original shelf on a Saturday and received the replacement shelf on Tuesday. Note to self: remove the glass crisper drawer shelf first, then remove the shelf frame.

Unplug the refrigerator. Remove face plate located in the upper back of the refrigerator compartment. Remove face place bracket on the right using nut driver. Removing these screws also frees the metal case enclosing the Defrost Timer. Pull the case away from the back of the refrigerator exposing the Defrost timer. Remove the electri ... Read more cal plug from the Defrost Timer. Then remove the Defrost Timer from the case by removing the two screws securing it. Reverse the procedure to install the new Defrost Timer.

The procedure was straightforward. I removed the cardboard backing on the lower back of the refrigerator to expose the fan unit. I then undid the electrical harness at the fan. I then removed the three screws securing the fan motor to the metal bracket. This is the hardest part in that I had to reach through and get to the screws with my ... Read more small tools. I then removed the old motor and blades and placed the new motor and blades. Again, a bit tricky trying to get the three screws mounted into the bracket...small tools and hands helps. After that I used the electrical harness supplied with the kit to plug into the new motor and I was done.

rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, c ... Read more lose up, reverse panel. ( 20m). i also took time to clean grilles with small vac and damp rag, ( looks and sounds like new) bob Wi.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only ... Read more swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

Very pleased with the delivery time. Was able to repair the refrigerator before the beer got hot. Replacement was easy.
Removed blower housing. Replaced motor. Put blower housing back in place.

I unplugged the power cord. Then, I removed the housing at the inside-top of the refrigerator by removing the two screws that hold it in place. This exposed the defrost timer. I removed two clips that hold the timer in pace. Then unplugged and removed the old timer, and plugged-in and secured the new timer. Then, screwed the housing ... Read more back to the top of the refrigerator. Just be careful, I partially broke the tops off the two pins that slide through the timer's body (when attempting to removed the clips that sit on the pins). Not a big deal, as the timer will remain in place without the top of the pins. Next time, I would cut the clips using diagonal cutters.

We took the edge out of the slot and pulled the old one off then put the new one on. Once we got the plastic edge started into the slot it was a breeze. Only took about 5 minutes. We were very pleased with the results.

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the c ... Read more ables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

Through experience I determined the problem was with the compressor trip switch. It's the small white piece that looks like a flat fuse.

The parts arrived in 3 working days. Instructions were included - very easy to understand. From start to finish I replaced the switch in about 15 minutes. Frig is now working perfectly.
... Read more />
3 pieces come along in the kit - however, all I needed was the switch, but for the price I changed out all three to assure compatibilty.

I also ordered the cover which was not needed.

A Happy Customer! {:-)