ATB15 Refrigerator - Instructions

If the fan blade needs replacement you will hear a loud noise coming from the refrigerator while the refrigerator cycles on. It will go away when it cycles off. (Note: in many cases you only need to replace the fan blade and retaining clip. Purchase both parts together. I thought I could use my old clip just to find out that the fan b ... Read more lade design changed and the old retaining clip would not work.)

NOTE: My refrigerator has an ice maker. delete the steps for the ice maker if you do not have one.

- I call the evaporator cover the back panel.
- I call the tunnel assembly the fan cover.

1) Empty contents of freezer - Only freezer. (Note: leave refrigerator section alone) Remove wire rack by lifting and pushing in one side to free the other side. It may be a bit of a struggle but the holes that the wire rack sit in are recessed in the middle to allow removal. (Look at other wire rack holes to see where the holes exist.)

2) Set dial in refrigerator to "OFF" then unplug refrigerator (safety first)

3) Remove one screw below the ice maker holding the ice maker to the side of the cabinet.

4)Push up on ice maker - Slide Ice maker up and dismount from mounting bolts.

5) Once the ice maker is dismounted you will expose the ice maker wiring harness - Unplug ice maker harness from rear panel.

6) Remove ice maker.

7) Remove ice maker mounting bolt closest to rear of refrigerator to facilitate removal of back panel.

8) Remove 4 screws on back panel and slide panel toward you.

9) Un-clip wiring harness attached to back panel that serves the ice maker (this protrudes from the back panel.) and push it through the back panel -

10) Lay panel down and unclip fan housing (Tunnel Assembly) from back of panel (Evaporator Cover) (note other instructions will tell you to remove this before the back panel. I found it easier this way. (Note the fan is attached to the back panel (Evaporator Cover).

11) After the fan cover is un-clip it hinges from the top. Lift panel - unhinge fan cover and expose fan.

12) The fan has a clip on the end that looks like a compressed wire spring. Pry off with a flat tip screw driver.

13) Pull fan blades towards you and remove from motor shaft.

14) Inspect shaft and wipe it off.

15) Press new fan blade assembly on shaft with you fingers. you will be able to see the shaft from the front of the fan blade as the fan blades have a split in hub area. Seat the fan blade on the shaft as far as it will go.

16) Install new fan blade clip (I used a flat screw driver and pushed it on the fan blade by working different sides of the spring (be careful).

17) Reassemble in reverse order.

I hope this helps. The job is reasonably easy for the novice and will save on a repairman coming out to install a fan blade and clip which is really a 15 minute job for the professional.

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the c ... Read more ables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

Cooling coils froze up. Removed back panel in freezer section. After thawing coils, manually advanced defrost timer to check if fan stopped and defrost (heat) strips energized. Fan did stop, but heating strips did not energize to thaw coils. Used electrical meter to determine circuit was open at defrost thermostat. Ordered replacement and ... Read more installed in about 20 minutes. No issues so far.

Unplugged refrigerator, removevd 4 hex head screws in rear panel of freezer. Gently pull panel forward and rotate panel to left side of freezer to expose coil. (If you have an ice maker you will have to remove this unit first) If no ice maker plastic plug will fall out of panel when you pull it forward. Set aside it aside.
Disconnect ... Read more heater connections. (1) wire on each end of heater. Disconnected (2) wires that connect defrost t-stat. Removed (2) metal clips that hold defrost heater shield and defrost heater to coil..
pulled t-stat off of refrigerant line on right end and replaced with new. (It is only a little spring clip that is part of the t-stat) Replaced defrost heater. Reversed un-install procedure for metal clips and wiring. Gently plug wires in (do not pull on wires) Put rear panel back in place, put in the 4 screws , hand tighten only (just to snug) gently push on panel to make sure it is back as far as it will go..check screw tension again. Put plastic plug back in drain hole or re-install ice maker. Plug the refrigerator back in. This should not take you more than 30 min. max. I do not have an ice maker so it only took me 15 min.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

The center hub of fan blade had cracked and had slipped off of fan motor shaft. I replaced fan and motor by pulling the shelf from freezer, removing 4 screws holding freezer back panel, tipped panel out and removed/replaced fan. Reassembled and it worked fine.

My husband replaced the condenser fan. It took awhile and a few choice words but he got it replaced. The fan seemed to work fine, but it still wasn't cooling. I noticed that when we had the fridge unplugged that water started draining out the dials at the top of the fridge under the freezer. And there was absolutely no water at all in ... Read more the drip pan under the fridge. So I took the doors off and totally took the inside of the freezer apart. I discovered that the styrofoam on the floor of the freezer had become inudated with fluid and the under the foam the coils were all frozen solid with ice. Hence not allowing any drainage. I put a lamp in the freezer area and defrosted all the ice. In searching the internet i discovered that they no longer produce the foam so i went to home depot and got a piece of foam and aluminum foil and cut it to replace the ruined foam. I put the fridge all back together said a prayer and crossed my fingers and lo and behold it works perfectly now!!!!

Remove the back hardboard cover screws for access to the condenser fan. I opted to tip the fridge over on its side for even better access to the fan mounts and wire. Replaced the fan assy (reused the fan). Splice the wire and it's done.

I saw on a partselect web site that these symptoms could be caused by a failed condensor fan motor. After removing the cardboard panel in back of the refrigerator I noticed the fan was not running when the rfigerator was. The fan was held in place by three brackets. I unscrewed the screws holding the fan motor to the brackets and also uns ... Read more crewed one of the brackets to make room to pull the motor out. I cut the wires close to the motor. I removed the fan blade and secured it to the new motor. I had to reroute the old wires in order to have enough slack to use wire nuts to attach them to the leads on the new motor. I then re-attached the motor to the two brackets remaining in place and then re-attacehed the third bracket I had removed to get the motor out.. The most difficult part was working in a very confined space.

First I removed the Ice bin, I then loosened the ice bin rail under the ice maker and removed the screw that attached the bottom of the ice maker to the side of the fridge. I unplugged the power to Ice Maker from the back of the fridge and unscreewed the two screws that secured the ice maker to the fridge. This allowed the Ice Maker to ... Read more be removed from the fridge. To replace the new ice maker I simply repeated the steps in reverse.

Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installin ... Read more g the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.

After moving the refrigerator away from the wall I removed the cover on the lower back of the unit by removing the screws that held it in place. The condenser fan was not turning and there was heat build up in the area causing the refrigerator to not work properly creating elevated temperatures in both the freezer and regrigerator. Remova ... Read more l of three torx screws from the original motor was all it took to get the motor free. By turining it and working the fan blade around the mounting bracket I had the motor out in just a few minutes. Replacing the new motor was just as easy to reinstall. The fan was removed from the old motor and placed on the new for installation. The original motor was wired to accept a connector from the wiring harness of the refrigerator. I simply cut the connector off the wiring harness and stripped the insulation from the wires which easily allowed me to connet the wires of the motor and harness with two wire nuts. Three self tapping screws were used to hold the motor in place replacing the torx screws. Installed I plugged the unit in and immediately the fan started spinning as the unit came to life. Cleaned and replaced the cover over the back and slid back into its spot. Running as good as it did when it was new. Easy job to take care of.

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator i ... Read more n less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

I noted that the fan wouldn't run so I remove the trim so I could check the power. Once I saw there was power but the fan wouldn't run I was convince it needed rreplacement. To get the fan loose I had to remove the wiring and remove several screws. I then had to remove the fan blade with the needle nose pliers. I just reversed the ord ... Read more er of things to replace the fan motor and put the refrigerator back together.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened th ... Read more e screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!