The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
Ice maker not working.
2 of 2 peoplefound this instruction helpful.
kurt from Westminster, CO
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
This was a very easy repair. Of course start by unplugging the power cord. Take out the lower freezer drawer. Unplug the wiring harness from the ice maker at the rear of the freezer. Undo 3 screws with a 1/4" nut driver. The ice maker will come right out. You don't have to undo any water connections, the feed tube just slides into a g
... Read moreuide in the ice maker. Once the ice maker is out, unplug the harness from the old one and snap it into the new one. Same with the cover. Reassemble in reserse order. Plug the power cord back in and wait a couple of hours for the familiar sounds of ice cubes falling into the tray.
Read less
Was this helpful?
Thank you for voting!
Ice maker putting black pieces of plastic in the ice
2 of 2 peoplefound this instruction helpful.
Doug from Lewisville, TX
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
Replaced ice ice maker using All of the instructions on the website. Very easy. A couple of the screws I had To feel for because I couldn't gety big head In the freezer far enough to see them. Very simple and only took about 15 minutes.
Was this helpful?
Thank you for voting!
Ice tray filled up with water. Stopped making ice.
2 of 2 peoplefound this instruction helpful.
robert from COLDSPRING, TX
Very Easy
15 - 30 mins
Screw drivers
As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.
Was this helpful?
Thank you for voting!
Ice Maker Leaked Creating an Ice block
2 of 3 peoplefound this instruction helpful.
Loren from Indianapolis, IN
Really Easy
Less than 15 mins
Screw drivers
Merely remove the front bottom screw that attached the ice maker to the refrigerator Lift the ice maker gently off of the 2 top screws Unplug the icemaker wiring harness from the back of the refrigerator, and remove Snap off the end of the maker and remove the keeper for the wire arm Remove the wire arm and install on
... Read morenew maker Unplug the wiring harness from the old maker and plug into the new one Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker Install bottom screw into the bracket that holds it in place. This took less than 5 minutes.
Read less
Was this helpful?
Thank you for voting!
refrigerator was overheating, condensor fan dead.
2 of 3 peoplefound this instruction helpful.
David from Granada Hills, CA
Really Easy
15 - 30 mins
First I removed all the screws from the back cover. 2nd removed fan nut and fan blade 3rd removed fan bracket 4th I traced wire to the condenser and disconnected wires from wire nuts. Installed existing fan brackets to new motor kit then reconnected wire nuts to new motor cord Reinstalled fan nut and blade
... Read more, reinstalled cover, plugged it in and BAM .WORKS PERF!
Read less
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 peoplefound this instruction helpful.
Gail from Golden, CO
Really Easy
Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
The screws didn't work. Had to use old ones.
2 of 3 peoplefound this instruction helpful.
Cheryl from Hornell, NY
Really Easy
Less than 15 mins
Screw drivers
Just used a screw driver. It was real simple.
Was this helpful?
Thank you for voting!
Replaced Ice Maker
2 of 3 peoplefound this instruction helpful.
Steven from Clinton Corners, NY
Easy
Less than 15 mins
Nutdriver
Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.
Was this helpful?
Thank you for voting!
icemaker quit working
2 of 3 peoplefound this instruction helpful.
craig from green bay, WI
Really Easy
Less than 15 mins
Nutdriver
I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.
Was this helpful?
Thank you for voting!
Dropped a water pitcher in the fridge and shattered the glass shelf
2 of 3 peoplefound this instruction helpful.
Rodney from Forest Hills, NY
Really Easy
Less than 15 mins
First, the part arrived within 2 days of ordering. And this part wasn't available anywhere but here. Here's how hard it was to fix:
Open package. Glance over instructions. Slide shelf in groove. Align drawers and mount to shelf.
Done.
Was this helpful?
Thank you for voting!
The bottom brackets on the inner door were missing.
2 of 3 peoplefound this instruction helpful.
Linda from Saginaw, MI
Really Easy
Less than 15 mins
The frig had broken brackets on the inner door. I connected the clips to the trim piece and I snapped the entire piece into the slots on the door. Presto! All finished.
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
3 of 6 peoplefound this instruction helpful.
John from Greensboro, NC
A Bit Difficult
30 - 60 mins
Nutdriver
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right
... Read moredirection. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
My Orders
