AST- - Parts

This individually sold grommet is a genuine OEM part and is used for a variety of different small engine/outdoor lawn equipment. The return fuel line from the carburetor is installed through this grommet, which creates a seal to prevent future leaks and ignition issues. Over time and through exposure to fuel, the grommet can wear down, le...Read moreading to cracks, tears, and missing pieces. If you notice fuel is leaking during operation, or are having issues with starting the engine, this grommet may be the cause. Depending on your model, installing the return line in the grommet and then installing both together in the fuel tank may be easiest, rather than installing them separately.

The fuel pipe/fuel line assembly is a genuine OEM parts kit used in gas-powered outdoor equipment with dimensions of 5mm x 160mm. It includes a pipe or line, which carries fuel from the tank to the carburetor, and a rubber grommet which holds the fuel line in place. The grommet also has a flange that prevents it from being pulled into the...Read more body of your equipment. Over time the grommet may wear down and the fuel line can become brittle and crack causing fuel leakages and difficulty starting or running your equipment. Therefore, it is important to routinely inspect this assembly and replace it when it shows signs of wear. Before your repair, drain the fuel for your safety and to prevent contaminating the fuel tank. To install a new fuel pipe assembly, simply pull off the old grommet and detach the fuel line. Carefully insert your new fuel line into the new grommet and connect the line to the carburetor and the fuel filter inside the fuel tank on your equipment.

Also known as a priming bulb, this OEM replacement part is an individually sold rubber primer bulb. Since it is made of rubber, it will eventually lose its elasticity and crack or break,and need replacing. It is designed for use with a variety of different small engine equipment and is also known as a purge bulb. Pressing this primer bulb...Read more forces fuel through the fuel line and into the carburetor from the fuel tank. Once the carburetor is has a sufficient level of fuel, any excess fuel will be forced back into the fuel tank through the return line attached to the carburetor. If your primer bulb has a darker appearance or has lost its elasticity and does not return to its original shape, it means the rubber will likely soon crack, which will lead to fuel leaking into the engine and ignition system. To replace your primer bulb, simply remove the outside cover and primer bulb cover and replace the bulb within its housing.

This is a genuine OEM replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article and vide...Read moreo on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.

This OEM-made cleaner element, also known as an air filter, helps keep the engine clean by filtering the air that goes inside. It is 1/4 inches in height, 3 1/2 inches in length, 1/2 inches in width, and usually found in a housing near the engine of your lawn equipment. To check if it is broken, look for tears, holes, and debris on it. Wh...Read moreen the filter is damaged or clogged, it restricts the airflow in your machine. This can cause problems like potential misfires, expensive repairs, and even engine failure. To replace your cleaner element, you will need to access the element housing and remove retaining screws or clips using a socket or screwdriver. Once you slide out the housing cover, lift the element out of your machine. Prior to installing the new cleaner element, it is advisable to refer to your owners manual as your machine may have specific instructions for this procedure.

This item has been OEM sourced to ensure a high level of quality. The clip is intended to be used with trimmers and blowers from Hitachi and Tanaka. The metal clip is part of the fuel system. The clip is used to fasten the fuel filter and the fuel line assembly. This part is priced as an individual replacement part.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Tanaka and Hitachi lawn and garden equipment. The purpose of this gasket is to provide an air-tight seal for the carburetor, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. ...Read moreIt is a high-quality item that is made of durable composite material and is sold individually, over time it may wear out and begin to crack eventually requiring a replacement.

This is a genuine Tanaka replacement part that has been sourced from the original manufacturer to be used with trimmers, edgers, hedge trimmers, blowers, and gas powered drills. The plastic pulley is used to store the starter rope and to engage the starter cam. This item is sold as an individual replacement part.

This is a genuine Tanaka part for use with Trimmers and Edgers. The throttle lever allows you to control engine speed. The most common reason for replacing the throttle lever is if it is damaged or not engaging the throttle properly. This part is sold individually. The tools that you will need to replace the throttle lever is a T-25 Torx head screwdriver and a flat-head screwdriver.

This is an authentic Tanaka replacement part that has been sourced from the original manufacturer to be used with bike engines, chainsaws, blowers, gas powered drills, edgers, generators, trimmers, and powered augers. This screw is used with a variety of different types of machines and the application of the screw can vary based on the model of the equipment. The screw is available as an individual replacement part.

This is a genuine Tanaka replacement part, sourced directly from the manufacturer. The oil seal is found in many Tanaka power tools such as chainsaws and brush cutters. This part is a metal ring with a high-quality plastic inner ring, and is used to prevent oil leaks or contamination of the crank case. You may need a screwdriver and wrench to replace this part. This item is sold individually.