ASD2625KES Amana Refrigerator - Instructions

Simply cut the water tube on both sides of connector and push in the new one.

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ... Read more ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

Truth is, this took a couple hours of cursing, but that was due to poor information and no prior experience. I imagine the next one would take 20 minutes. The issues are these: videos tell you to use a putty knife to pry the old switch out. That is harder than it seems because each switch has a plastic spring that pops open to hold the ... Read more switch on, and you can't access the spring when the switch is installed. So it is important to use the knife on the side of the switch (left or right of spring -- look at the new switch), and back and forth until the switch is worked out. Then it can get worse. The new switch has to plug in electrically before it can be installed mechanically. In my case, with the switch on the fridge wall rather than the top, the outlet for the plug was encased in foam insullation. That gives the appearance that the plug was fixed, immovable, which makes it impossible to plug it in electrically before the switch is in place, and of course once it is in place you can't then plug it in. The problem here was poor instructions. Just scrape out a lot of the foam around the plug and you find that the plug is really not fixed, but attached to reasonably long wires that allow you to plug it in with the switch a couple inches from the wall, and then insert the switch. None of the online instructions tell you this about the wires.

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same t ... Read more ime to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Very easy to order from parts select. Took seconds to replace.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to ... Read more reach 10 degrees F to operate.

I had to order three times before I got the right part. This was due to my rush to fix the problem and not studing the diagram carefully (black and white diagrams are not that clear). The repair was very simple. Just remove the rubber from the plastic door and slip on the new one.

First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Ref ... Read more er to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!

I removed the two screws on the Ice dispenser housing and dropped it down. I catalogued all the electrical connections on a piece of paper for reassembly and basically followed my nose. I gave my wife the honor of testing it and I held my breath. Replacing this part was a breeze and it functioned perfectly when the job was completed. I ... Read more wish I had done this three years ago when it failed! Thanks very much !!

First I checked to see if the water pump in the base of the refrigerator was working properly. To do this, I removed the water filter, placed the by-pass cap on the water filter head, and dispensed water. The dispenser worked very well so I knew it was not the pump. I had just bought a new filter so it was okay too. So I figured it wa ... Read more s the Water Filter Head assembly. To install, I followed previous advice on Part Select website and followed a YouTube video that was excellent (enter "Refrigerator Water Filter Head and Tube Assembly-How to replace). Best advice...Styrofoam block that inserts from back of refrigerator where tubing enters...when removing, push it out from the inside of the refrigerator to avoid breaking it into pieces. Other good advice, unplug refrigerator and turn off valve to icemaker and water dispenser. Easy repair, could do it in half the time now because I was very careful when installing this item. Results: Excellent flow from dispenser!!! And better ice cubes too! Well worth the effort.

Replaced the relay and capacitor it runs.

Unplugged refrigerator.
Removed water drip tray.
Removed two Phillips screws.
used putty knife to
get behind outer plate and popped it off.
Disconnected electrical connections.
Removed the 4 nut driver screws.
removed ice maker door.
Removed seal around old Ice shoot flap and cleaned.
Removed i ... Read more nsulator pad from old ice maker flap and cleaned.
Installed seal and insulator pad on the new chute door.
clipped new chute door intact with seal and pad in place and snapped the top clips into place.

Reversed procedure to reinstall refrigerator parts.

Plugged in refrigerator and tested. Had no issues.

Problem led to 3 possible problem parts, defrost thermostat, defrost heater or defrost control board. Defrost heater ohmed out to 31 ohms, so seemed good. Defrost thermostat was open when warm but was open after running refrigerator to get freezer side cold enough for thermostat to close, it did not I thought. So I ordered thermostat. ... Read more Once part came in, I cut up a couple inches on orange and brown wires, stripped off enough to work with. I soldered new one in and heat shrunk the wires. I turned on and it seem to work and all night. Working fine right now.

First turned off the water and unplugged the refrigerator and then removed the old ice maker by first removing the side cover plate and then next removed the ice level detector. Remove the screws that hold the ice maker in place and rotating it somewhat soas to gain access to the wires and then unplugged them. Next I had to modify the way ... Read more the water comes into the new icemaker by adapting a CPVC street ell to fit into the hole on the side and then hook up the water supply. Installation is just the reverse of removal.