ASD261 Amana Refrigerator - Instructions

remove top plastic cover / phillips screw driver
remove top door bracket / 5/15" socket
lift off door
remove pieces of old cam / phillips screw driver
replace cam/ phillips screw driver
replace door
replace top bracket / 5/16" socket
check alignment

Removed screws from cover tested for power to motor found power was on to motor but motor did not work. I went to your web site was able to locate part in about 5 minutes . Even with over night shipping the part came to about $50,00, far cheaper tha a service call would have been.

Thanks John Paulsell

Turned old one until it snapped out. Replaced it with a turn.

This is a side-by-side refrigerator. The crushed ice wheel is part of the icemaker bin auger, and it began to fragment, popping pieces of plastic into the ice dispenser and on into our drinks. The manuf. manual had nothing about parts in it, so GREAT thanks to Partselect for their website!!! Now, to dismantle the bin and auger is simpl ... Read more e on this design: remove the bin from the freezer and allow it to defrost and dry; there are two small phillips-head screws on the front underside of the bin, holding the front panel in place - remove these screws and pop the front cover off; you'll then see two small phillips-head screws holding the auger-cap in place - remove these and pull the auger cap out, along with the auger; using a small pliers, remove the nut from the auger at the auger-cap, then slide the auger-cap off; at this point you just start removing washers, blades, etc, from the auger - MAKING SURE YOU KEEP THEM IN ORDER - until you reach the crushed ice wheel; separate the wheel from its metal brace, slide the wheel off and replace it; gradually replace all the other parts in order, cleaning them as you go, and simply put everything back together. It helps to keep the exploded parts diagram at hand - available on the Partselect website. It was a snap. The ordering process was simply and the part was delivered to my door on the second day after ordering.

First I removed the Ice bin, I then loosened the ice bin rail under the ice maker and removed the screw that attached the bottom of the ice maker to the side of the fridge. I unplugged the power to Ice Maker from the back of the fridge and unscreewed the two screws that secured the ice maker to the fridge. This allowed the Ice Maker to ... Read more be removed from the fridge. To replace the new ice maker I simply repeated the steps in reverse.

Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installin ... Read more g the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.

I changed out the water valve behind the refrigerator that controls when the ice maker and water dispencer receives water. It was easy. I removed the lower back panel to get access to the valve. Pulled the hoses out by pushing up on the ring between the valve and hose and the hose came right out. I disconected the power lines. Of course t ... Read more he water was disconected and power plug out prior to starting the job. I replaced the valve and reconnected the lines and power. I put the back panel back in place and turned the water on to check for leaks. The next day I had ice in the ice maker.

Begin by turning off the water source from the wall, next using a line wrench, remove the brass water line fitting nut from the copper water line from the wall. Next remove the second water line from the plastic push fitting by depressing the fitting to release the water line. Remove the Styrofoam insulation piece that resides between the ... Read more water lines that run into the refrigerator, then pull the old filter head out. Reverse steps for installation.

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator i ... Read more n less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

It's good to note, first, that the dual water valve on Amana fridges are notorious for cracking and leaking, either due to the fridge being left in the cold (the water inside the valve freezes and expands, cracking the water valve) or from issues related to shipping. Read the reviews, here - it's a common issue, but easy and cheap to fix ... Read more yourself. Here's my steps. I first turned off the water source to fridge by closing the correct valve. Next, I unplugged the fridge from electrical and from the water source line. When looking at the back of the fridge, I unscrewed the bottom left cover plate from the fridge body. After unscrewing and removing the plate, I made sure to note which lines came from which areas of the fridge and where the lines ended up at the dual water valve, and how they were routed through the plate and into the valve. The way this fridge is setup, the water source line screws into a main line that heads to the top of the fridge where the water filter is (like a "line in"). There's another line that heads back down to the bottom of the fridge (line out). The "line out" inserts into the outside plug of the dual water valve. The two lines coming out of the dual water valve are different sizes. Make sure to note which line goes to the icemaker and which line goes to the water dispenser inside the fridge. Once I knew which lines needed to go where, I grabbed my empty bucket, pulled the water lines out of the dual water valve with some pliers, and emptied the water into the bucket. After cleaning up any water splatter with my dry towels, I unscrewed the dual water valve from the plate. Once the old dual water valve was removed, I replaced it with the new valve and screwed it back into the plate. I cut off just a bit of the water line ends that were damaged due to pulling with the pliers, and then inserted them back into the correct spots on the dual water valve. I screwed the plate back into the fridge, reconnected the water source line (make sure to use some kind of water sealer tape or putty), plugged the fridge back into the electrical socket, turned the water source valve back on, and waited for leaks. No leaks! Once I was convinced there weren't any leaks, I had to bleed the water lines for about 20-30 minutes (it takes FOREVER...) by putting my bucket under the water dispenser inside the fridge and holding the water button for what seemed like an eternity - until the water was streaming steadily out of the dispenser. Voila! Good as new! Keep in mind that I didn't go through ALL the minute parts of each step - that would take too long. I'm believing that you'll be perceptive enough to catch the small things like looking at how the lines are routed into the dual water valve and where things are screwed into. Use your BRAIN, and you'll be fine. :-)

Freezer would get cold at bottom and some of the refrigerator. Took of freezer back panel and located freezer fan. Took a meter and saw power was getting to it, but not working. Removed fan and replaced with new on, working like a charm. Cold air was not circulating enough throughout the unit because fan was not working. It was not t ... Read more he thermostat or adapter control.

With the repair parts ordered and received from PartsSelect.com, I was able to install a new Ice Bucket and the crushed ice agitator assembly. This simple repair has the refrigerator dispencing ice like new.

The part was an exact match to the old one and the instructions from your website were all I needed to complete this repair. My wife thinks I am somewhat of an appliance genius now. Could not have done it without you...thanks

I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered ... Read more the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.