Freezer not defrosting coils refrigerator side getting warm
7 of 7 peoplefound this instruction helpful.
Randy from COUSHATTA, LA
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
Refrigerator side top unscrewed hex screws unscrewed Phillips screws remove circuit board unplugged connects and installed new board in reverse order
Was this helpful?
Thank you for voting!
Loud knocking noise coming from back of refrigerator when dispensing water. Very little flow. Problem was intermittent.
7 of 7 peoplefound this instruction helpful.
Patrick from PALM COAST, FL
Really Easy
15 - 30 mins
Nutdriver
Shut off water supply. Unplug refrigerator. Removed lower back cardboard panel. Removed two screws holding inlet valve bracket to side frame. Pulled valve out far enough to gain access to water lines and electrical connectors. Used 9mm open end wrench to press in collars to remove water lines from inlet valve. Used small container to catc
... Read moreh water dripping from lines. Removed defective valve and replaced with new one by first pushing water lines into respective openings, make sure they are fully seated. Reconnected electric wires. Installed inlet valve on side frame. Replaced back panel. Plugged in power cord. Opened water supply. Flushed about 2 gals of water through system. Note: water may not flow immediately due to air in water lines.
Read less
Was this helpful?
Thank you for voting!
light in refrigerator went OFF when in installed the new water filter
7 of 7 peoplefound this instruction helpful.
LUC from PALM DESERT, CA
Very Easy
Less than 15 mins
STRANGE ! to moment I installed the filter ALL the internal lights in my refrigerator went OFF and never came back.
Strange !! refrigerator works fine but no more light in it !!
35 year old water tube became brittle and cracked; leaking water
8 of 10 peoplefound this instruction helpful.
Melvin from OPELIKA, AL
Very Easy
Less than 15 mins
Screw drivers
Unscrewed clamp holding water tube to refrigerator ice maker. Pulled water tube from ice maker and water valve inlet. Cut the new tubing to the exact same length and inserted one end to the water valve inlet and the other end to the ice maker then screwed clamp holding water tube back to the refrigerator ice maker.
Was this helpful?
Thank you for voting!
Replacing the water filter.
10 of 17 peoplefound this instruction helpful.
Sandra from Altoona, AL
Really Easy
Less than 15 mins
Lift up on the water filter door to open. Pull out the old filter while noticing the arrow pointing up on the filter. Pull off the green caps on the new filter and pop the new filter in with the arrow pointing up as on the old filter. Push in until the filter snaps into place. Close the filter door. Push reset on the water filter button
... Read more on the freezer door to reset. Very easy!
Read less
Was this helpful?
Thank you for voting!
broken drawer
8 of 12 peoplefound this instruction helpful.
Thomas from North Port, FL
Really Easy
Less than 15 mins
replaced
Was this helpful?
Thank you for voting!
Broken Door Bins
7 of 9 peoplefound this instruction helpful.
elisa from richlands, NC
Really Easy
Less than 15 mins
Placed bin on the door and done
Was this helpful?
Thank you for voting!
Crack in vegetable drawer
6 of 6 peoplefound this instruction helpful.
Paul from NAYLOR, MO
Very Easy
Less than 15 mins
Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee
Was this helpful?
Thank you for voting!
Icemaker Wouldn't Work
7 of 9 peoplefound this instruction helpful.
NANCY from KEOKUK, IA
Really Easy
15 - 30 mins
Screw drivers, Socket set
I removed the screws that attached the drum housing to the bin. I detached the auger & removed the broken drum assembly, turning the auger to the right, opposite what I thought it should be. I slipped the end of the auger into the new bin coupler & put it in place at the rear of the bin. Next I slipped the auger drum into place & ti
... Read moreghtened it to the left with a socket wrench. I screwed the drum housing to the bin, put the bin back into the freezer & I now have ice through the door again. Easy repair even for me, a 60+ woman.
Technician at ASK suggested replacing ice maker. Ordered new ice maker(prompt delevery)then noticed it came without wire arm and white platic "flag". Ordered arm and "flag", replaced all old with new and seems to be doing well. Perhaps all I needed was the plastic "flag" on the limit arm wire. Will never know. The new icemaker wiring had
... Read moreshort wires and a connector. Old ice maker had no connector so the short wires were removed and the old wires plugged into the ice maker. Mirror was required in order to see the side wall mounting screws. Very narrow work area, tiny freezer side.
Read less
Was this helpful?
Thank you for voting!
Ice Maker would no longer move ice through the dispenser
8 of 12 peoplefound this instruction helpful.
Sheila from Lena, MS
A Bit Difficult
15 - 30 mins
Screw drivers
As cookbook authors and publishers, my husband and I depend on our appliances. When our icemaker would no longer work, it was imperative that we repair it as quickly and ecomonically as possible. We had used PartSelect.com earlier to order a part to repair our Jenn-Air stove top and had great results. So, rather than paying a repairman
... Read more four times or more the cost of the part, we ordered the part and my husband installed it. It took less than 30 minutes to remove the broken auger and install the new one. THANKS PartSelect.com -- we'll use you for all appliance parts needs.
Read less
Was this helpful?
Thank you for voting!
Fan motor was making noise.
6 of 7 peoplefound this instruction helpful.
Harry from Mountain Iron, MN
Easy
15 - 30 mins
Nutdriver, Screw drivers
First I removed all food in freezer.Then removed selves and hanger brackets.Then the back panel and light cover.Then I unplugged motor but before this I unplugged refrigerator from the wall.Removed motor from bracket after pulling of fan. Reversed the order to install motor and put back together
My Orders
