ASD2523 Amana Refrigerator - Parts

If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator doe...Read mores not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.

This white ice bin auger drum comes with a washer.

This grille is located on the bottom of the ice/water dispenser to catch the overflow. (Black)

In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in the dispenser chute to let ice through when it is being dispensed. If you have the following symptoms such as: door sweating, difficulty opening or closing door,...Read more frost buildup, warm freezer section, or problems with ice dispensing, then this is a solution. The tools needed for this repair are a putty knife, needle nose pliers, and 1/4 inch nut driver. Wear work gloves to protect your hands when performing this repair.

This thermostat assembly is used in refrigerator units and freezers as a sensor. The thermostat senses the temperature increase in the evaporator during the cycle of defrosting and turns off when ice is melted. If you have any of the following symptoms, replacing your thermostat could solve the problem: fridge does not start, is too warm,...Read more too cold, runs too long, or will not start. The tools needed for this repair project is a putty knife, Phillips and flat blade screw driver, 1/4 inch nut driver, and needle nose pliers. Remember to unplug refrigerator from power source as a safety precaution. Refer to the manual provided by the manufacturer for further installation instructions.

This is an icemaker for your refrigerator/freezer. Take note that this part does not include the front cover, the wire harness, or the shut-off arm. These must be ordered separately or recycled from your old unit. This unit as a whole will allow your appliance to produce ice. This model makes eight radius ice cubes.If your ice maker is no...Read more longer making ice, dispensing ice, or if it is leaking, it will need to be replaced.

This refrigerator ice bucket is a genuine replacement component designed to store ice produced by the icemaker before dispensing. Compatible with a wide range of models from Whirlpool, KitchenAid, Kenmore, Maytag, and Amana, it is constructed from durable plastic to withstand regular use. The container is sold as a standalone part and doe...Read mores not include the auger or other internal components. Replacing a cracked or missing ice bucket helps restore proper ice storage and dispensing functionality. Installation is straightforward and typically requires no tools—simply follow the instructions in your owner's manual to ensure proper fit and alignment.

This switch is located inside the dispenser.

This part is also known as a shelf frame. This drawer cover is for refrigerators. Drawer cover has rail brackets under the cover that hold the drawer and allow the drawer to slide in and out on the rails. Follow the instructions in the owner's manual or installation guide when installing this part. This comes with glass.

This refrigerator glass shelf serves as a replacement for the crisper pan cover and is designed to sit securely above the crisper drawers, providing both a protective barrier and additional storage space. Crafted from tempered glass, it offers a durable and safe surface that helps contain spills and maintain organization within the refrig...Read moreerator. The transparent design allows for easy visibility of items stored below. Measuring approximately 16.5 inches in width and 13 inches in depth, it fits directly into the existing white plastic frame without the need for tools or disassembly. Ideal for replacing cracked or broken glass, this shelf restores both function and appearance to your refrigerator interior. Sold individually.

This filter cap is white in color.

This is the replacement water tube kit for your refrigerator. This tubing is made of plastic, is 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube, and may need to be cut. This water tube transports water to the ice and water dispensers. If your refrigerator is leaking, or if the ice and water ...Read moredispensers are not dispensing properly, you may need to replace this tube. This part is sold individually and is an OEM part sourced directly from the manufacturer.