ASD23 Amana Refrigerator - Instructions

As the prior stories mentioned, this was a fairly easy fix to a nagging problem. Heck, we almost bought a new refer over this, cuz the door would keep popping open.

Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I ... Read more didn't do that!)

With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.

Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!

Greg

Removed damper vent by hand and then unscrewed 2 visible screws that hold Damper Control Unit in place. After removing screws, the damper control unit is easy to remove by unplugging 2 electrical connectors by hand and connecting new unit the same way. Screw the panel and snap the vent back in place and you're done!! Piece of pie, easy ... Read more as cake...Ha! Ha!

On the back of the refrigerator, I unscrewed and removed the lower-right panel. As I peeled the insulation off the panel, the insulation would disintegrate, so I used a vacuum-cleaner hose to remove most of the insulation. I removed the remaining adhesive with my fingers. I peeled the backing off the new insulation, and stuck it to the pa ... Read more nel.

I had ordered two pieces of insulation, hoping to also replace the insulation behind the compressor, but removing the compressor was complicated and risky, so I returned the second piece of insulation.

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed

The other guy described it perfectly so all I can add is that this repair was as simple as they come. Don't hesitate.

1 - Look at the schematic for the "Fountain" on Partselect.com
2 -Order the ice chute door and seal (seal is rubber and eventually it will stop sealing - while you are in there go ahead and change it)
3 - Unplug the refrigerator then remove the sump tray by pulling it straight out from the door
4 - Unscrew the two screws hi ... Read more dden behind the sump tray - hold the dispenser front housing in place so it doesn't drop downward - after removing the two screws slide the dispenser front housing downward while pressing it against the refrigerator door - there are two clips on the back of the housing that hold it against the refrigerator door
5 - Gently pull the dispenser front housing out of the refrigerator door an inch or two - you will be able to see the electrical connections between the dispenser front housing and the refrigerator.
6 - Continue pulling out the dispenser front housing until you can reach the multi-wire connector on the left - the connector is held together by a clip on the bottom center - squeeze the clip at the end closest to the wires to release it - gently pull the connector off
7 - In the center of the back of the dispenser front housing is a black plastic box (the limit switch) - again, gently pull it away from the two clips holing it on
8 - Set the dispenser front housing aside
9 - Slip the water hose out of the clips holding to to the chute
10 - Unscrew the three screws holding the chute to the door (two on the left and one on the upper right - Slide the chute out of the door
11 - Hold the door hinge so you don't accidentally break it (personal experience) and unclip the top then the bottom of the ice cube door from the hinge (the ice chute seal and ice chute door insulation are attached to the ice cube door - take all three out at the same time)
12 - Slip the ice chute seal off of the ice cube door - pull the ice chute door insulation out of the ice cube door
13 - Put the ice chute door insulation into the new ice chute door - Slip the ice chute seal onto the ice cube door (the schematic will give you the proper orientation for all of the parts)
14 - Again holding the door hinge - slip the two "L" shaped clips onto the bottom of the ice chute door - rotate the ice chute door assembly and snap (gently) the two side clips into place over the opening in the door hinge
15 - Breath a breath of relief if you didn't break anything
16 - Slide the chute assembly over the white pin on the lower right of the refrigerator opening that accepts the chute
17 - Replace the three screws that hold the chute assembly to the door - replace the water line
18 - Clip the limit switch onto the back of the dispenser front housing
19 - run the multi-wire connector behind the water line - connect it to the back of the dispenser front housing
20 - Slip the wires back into the clips along the sides of the opening in the refrigerate door
21 - Rest the dispenser front housing on the bottom of the door opening - it must fit flush to the door (top, bottom and sides) - Slide it gently upward until it stops - replace the two screws at the bottom rear of the dispenser front housing - slide the sump tray back in place
22 - Plug in the refrigerator
23 - Dispense ice cubes into a high ball glass and enjoy a job well done

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Removed pop off plate inside top of refrig.
Removed 2 screws holding cover.
Removed cover and styrofoam piece
Unplugged wiring
Removed old part
Transferred wiring to new part
Replaced all parts.

Followed the video and installed the new Jazz board. The board cam in 1 piece which had to be separated into two pieces, but the scored area on the board made it less intimidating. At the same time I replaced the two incandescent lamps in the refrigerator area with LED lamps. Getting the housing for the control board apart was the most ... Read more difficult part, installing the replacement board was a breeze.

My son (who does HVAC, but not appliance repair) did some investigating by taking front and back panels off and determined that the evaporator coil was freezing over because the defrost wire was not heating up. He and his girlfriend did some real-time internet searching for diagnostic info because NO control diagram was included with the ... Read more refrigerator. He determined the problem was most likely the electronic control board. Ordered and installed a new board and the refrigerator is back to working fine. Took about 2 hours to diagnose the problem and 1/4 hour to actually install the control board. Kind of disappointing that this control board failed when the refrigerator was less that 4 years old.

By sliding athin screwdriver blade down the side of the old switch the expasion prong that hold the switch in place was compressed enough to allow the switch to come out easlily. Plugged in new swithc and snapped in place. Plugged the refrigerator back in and light has worked great sense!

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. ... Read more drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there w ... Read more aiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

I didn't. Don't know how to get to light bulb to change it for this specific model