AS2625PEKB Amana Refrigerator - Instructions

replaced drain hose; melted ice that had built up behind it

replaced electric control board, defrost for six hours. next day (24 hours) same problem, [email protected]

I followed the other web notes with one change .Since I too forgot the lube , I used a pry bar and block of wood to lift the door and a tooth pick to glob some lube in the lower hinge.

The worst part was unloading the door shelves. Removed upper hinge cover and hinge hex screws. This allows the door to be removed. Lay the door on side. Remove screw that holds cam in place. Replace
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuf ... Read more f.

Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge.
Probably took about fifteen minutes total.

Remove the grandkids pictures from the door then empty the contents inside the door. Remove the top hinge cover and the top hinge bracket. Lift the door off the bottom pivot. Replace the lower cam by removing one screw. With the door in the horizontal position, remove and replace the upper cam. Apply a little grease on both cam surfaces. ... Read more Align the door before tightening the top bracket and your done. If you did not take a picture of the door before you started the project you will have to rely on memory to arrange the pictures in the proper location.

Within a 2 months of purchase the compressor on This refrigerator this unit failed. and again two years later. After all of that, we were pleased to find a replacement dairy door for this unit. thank you!

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

plugged the two wires in and snapped the switch into it's socket.

I have never used the ice maker because I have a well and didn't want to usewell water to make ice. I usually make ice with bottled water.
I decided to try making ice with gravity fed water from a converted water fountain placed on a higher level than the refrigerator, locater in my garage next to the kitchen.
When I looked at ... Read more the rear of the frig. I saw a copper pipe (on the bottom of the frig.) that lead to a valve, with a plastic tube that went to the freezer. I didn't think that the gravity fed water could go down to the bottom and return to the freezer at the top, so I cut the plastic tube, and fed the water directly to the ice maker.
I only put a small amount of water in my water source because I wasn't shure what would happen. The water filled the tray and the rest of the water went to the container that catches the ice.
I did get one tray of ice. I later found that the valve that the copper pipe went to, has a 7 minute timer that only allows a small amount of water to pass.
My next effort will be to connect to the copper pipe and see if it will allow the gravity fed water to rise to the ice maker. Wish me luck

First I looked at the manual to prevent causing
further damage and read the instructions on how to remove the original parts. I then removed the broken door and attached the new one and replaced it back as directed. Voila!

The correct parts were shipped and installation was easy.

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wi ... Read more sh I'd thought to try this years ago when the old switch began to fail.

Ordered the part and it fit perfectly. Very happy and pleased with the success.

I watched the online video and followed the directions. The only thing that was not obvious (and this is where the video saved several minutes)was how to remove the upper part from the door. This repair makes the door seals much more effective and should reduce the compressor run time. I have to compliment you on your prices and speed ... Read more in getting the parts to me...great service!