AS26 Amana Refrigerator - Instructions

Removed the door by taking 3 screws out of the top and lifting straight up, then replaced with the new parts and very easily replaced the door, worked ike a charm, if i didn't know any better it was like factory new

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was oft ... Read more en used to repair this issue. The service was great and the delivery was fast.

Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back ... Read more on and checked the switch. Worked perfectly! Easy job.

simple . . . . the new shelf support slipped into place, made to fit, without tools or difficulty.

in stalled new circuit board an thermostat an was fixed

Unloaded refrigerator. Pulled refrigerator from wall. Removed bottom panel on back and replaced bolt. Reversed steps but leveled rear wheel before reloading.

I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work proper ... Read more ly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..

The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one or ... Read more ientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the ... Read more 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

Removed top hinge cover and socketed out hinge nuts. Lifted door off bottom hinge. Socketed out broken bottom cam and replaced with new. Reset door with someone lifting and the other guiding. Reattached top hinge and cover. Voila.

let out screws and put brackets in place

real easy

removed door.examined problem,. installed part. super easy

Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap ... Read more filter.I made that mistake! hope this helps good luck!

Super simple following the instruction video you posted. Thanks!

On several occasions the ice bucket had fallen inches onto other frozen foods and the auger wouldn't work. After dealing with this several times over a period of several years, I decided to see if I could locate a replacement which I did through your company; We took the old one out, unsnapped parts and then snapped the new bucket to th ... Read more e gate and shazzam, we were able to slide the new bucket into place and it works like new. Hopefully a repair won't be necessary again!