ARTC862 Amana Range - Instructions

replaced element

removed the screws disconnected the old one and connected the new one and put the screws back on it

I took a couple of screws out that hold the bottom
element in place replaced the old one with the new one and fired it up. Worked like a charm and maybe this old stove will live on to make more Roast beef dinners.
If it been any easier my 10 year old grandson could have done it.

This repair took less than 5 minutes, literally! Two screws released the element, then unplugged it from two connectors. Then plugged in the new unit and screwed it into place. Cheap and easy!

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

While trying to clean the oven, I decided to remove the lower heating element to make it easier. After removing the 2 screws on the bracket that holds the heating element in place, I pulled the heating element out only to short it out on the back of the oven and wreck the element. Luckly I was not injured or shocked, so if you need to d ... Read more o this, I recommend reading the owner's manual on how to property ground out the circuit first.

Anyways, to replace it, I just removed the lower panel on the back of the oven (roughly 10 screws). Installed the new element on the inside of the oven and screwed it into place. Then, connected the wires to the element from the back of the oven. Replaced the panel and turned the power back on.

In all, it took probably 15-20 minutes to fix and only cost me $37. I know that a minimum repair cost for this from Sears would have been $150, so definitely worth my time.

We unscrewed the old element by removing 2 screws and put the new element in place and put the 2 screws back in and it was done. Piece of cake!

I ordered the new part, which arrived in just 2 days. I did not pull the oven away from the wall, I merely turned off the electric, unscrewed the bad element, pulled it out enough to see the ends, and then I removed the existing wires using needle nose pliers. I put the wires on the new element, inserted it back into the oven wall, and sc ... Read more rewed it tight. I turned the electric back on, and checked it out. Worked like a charm! Only 40 bucks (including shipping), five minutes of my time, and I avoided an expensive service call. :-)

Removed 2 phillips screws and pulled elements out 3 to 4 inches. One of the leads touched the housing and blew the circuit breaker, so don't forget to unplug or turn the breaker off! Simply slide clips off and install on new element. push back in place and reinstall 2 screws. Very simple.
P.S. element was delivered very fast!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new wires, replaced the two screws and turned on the oven to test it. Easiest repair job I have ever done.

Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on ... Read more Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.

removed back plate screw, removed two broiler screws. Disconnected wires in back plate by sliding them off of connectors. removed broiler coil and assembly. Using pliers, bent retaining hooks off of old coil, removed it and replaced it with the new coil. Reversed process.