ARTC7522WW (P1143817NWW) Amana Range - Instructions

Removed 3 screws, lifted the top control panel. Adapted new plastic end panel and replaced new end cap an refastened with original screws.

Unscrewed all the phillips screws holding the door together. Re-assembly indicates that you want to note exactly how the sides overlap the front and back steel panels, possibly take a cellphone picture before starting. The front and back panel will bend down the bottom attachment metal tabs, misaligning the sides, etc if you replace the g ... Read more lass with the door still on the range. Prob. best to have a second standing by or remove entire door first.

Removed screws on edges of door. Romove front panel. Remove several screws around glass. Replace inner glass and replace screws. A little tricky reinstalling trim around door front.

Removed 2 screws from mounting plate in base element.

Disconnected 2 wires from bake element.

Installed new bake element in reverse.

Switch off the breaker or unplug.
The screws were in tight so make sure your philips bite is new so you do not strip.
Pulled the element out and held the wires in place with a clothes pin so not to slip back in the stove.
Connect and cooked up pizza for dinner.
Very easy

Removed two screws-put burner in-pit screws back in! Turned over on and it worked!!!

1. removed the screws that held the caps.
2. Moved the stove away from the wall.
3. Unplugged the power cord, for safety.
4. Removed the caps.
5. Install the new caps.
6. Plug the power cord in.
7. Place stove back in positon against the wall.

I first killed the power to the oven by switching off the circuit breaker and then unplugging it from the wall. With the oven pulled out, I removed the back cover panel to disconnect the lower (bake) element power leads from the broken element. I removed the two screws on the metal plate that attached the element unit to the oven and re ... Read more moved the whole bake element assembly from the oven. I then inserted the new element assembly into the oven and reattached the screws. The next step was to reattach the power leads to the new element. It was then time to put the back cover panel back on and plug the oven back in. I then pushed the oven back into place and switched the circuit breaker back on. Finally, I tested the new element to see if it operated properly by setting a temperature and observed the temperature on a separate oven thermometer used for baking. Your exploded views of the oven helped me plan and execute this repair. Good feature that would be even better if the resolution was a bit better.

removed 2 philips screws holding element, un plugged element. new element arrive next day, insalled in less then 1 min. turned on, setoven for 375 pizza in 20 min later

I read up about the repair on the internet and what it entailed, thought I could do it. So followed directions from the internet after looking up Ammana, model number and serial number, and ordered the part from Part Select.com. It arrived two days later, was really impressed with their business handling of it.
I paid particular att ... Read more ention to disconnecting the power and pulling the plug out of the wall as double insurance to not getting electrocuted.
The Installation was quite simple, just pull the old one out and put the new one in. I took note of how the old one came out, and connected the new one in the same fashion, and it works wonderfully, just heated right up. It was a good experience.

Unscrewed the 2 screws in the back of the element. Disconnected the unit from the bake of the oven, replaced the two ends of the new element and screwed in the 2 screws. Oven works great! Took less than 5 minutes to complete.
Thank you for the FAST delivery!!

unplugged appliance, removed 4 screws holding bacckplate on, slid new switch into place, unattached 3 wires remembering place and order, attached to new switch, reattached backplate, plugged appliance back in. Found it better to order part myself online from drawings of appliance than to telephone order -- got wrong part twice from teleph ... Read more one order. Online was easily able to pick out correct part from diagram.

Had to use wd-40 to get the old part loose (oven is over 15 years old) and used pliers to pull apart from the oven. Replaced with the new part and works great. . . Once I used the wd-40 to loosen, it was super easy.

ordered new broiler pan

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All ch ... Read more ecked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.