Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replaced cracked compartment door
2 of 3 peoplefound this instruction helpful.
john from NORWOOD, MA
Really Easy
Less than 15 mins
removed old and installed new compartment door by hand.
Was this helpful?
Thank you for voting!
Fan was not spinning make it not cold in bottom part
1 personfound this instruction helpful.
Dylan from WHEELING, WV
Very Easy
Less than 15 mins
Screw drivers
Take screws out pull panel out unconnect the part connect new one and your done
Was this helpful?
Thank you for voting!
GASKET AROUND DOOR WAS LETTING AIR IN/ COLD AIR OUT
1 personfound this instruction helpful.
Susan from BONNEAU, SC
Very Easy
Less than 15 mins
Put gaskets in the car dash to get warm (90 outside), Pulled off old gasket and brought new one in and just inserted it into the slot around door. Was a little buckled but it straightened out after a few hours. Was very easy!
Warm fridge and freezer but compressor was running. No air distribution inside fridge
1 personfound this instruction helpful.
Brian from BURTON, MI
Really Easy
15 - 30 mins
Nutdriver
I turned breaker off to fridge, it was easier than pulling fridge out in camper. I took 4 screws out of back panel that revealed the evap fan, took 2 more screws out to take fan bracket off. Unplugged fan plug. Took fan blade off the non working evap motor and put it on the new evap motor. Put all the screws back in the reverse orde
... Read morer and flipped the breaker and air started circulating.
Read less
Was this helpful?
Thank you for voting!
door hinge broke.
2 of 4 peoplefound this instruction helpful.
Bernard from DONALDSONVLLE, LA
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
Removed door and replaced bushing bracket was ok.
Was this helpful?
Thank you for voting!
The Light Socket Burned Out.
5 of 13 peoplefound this instruction helpful.
MATTHEW from STOCKTON, CA
Really Easy
Less than 15 mins
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 peoplefound this instruction helpful.
Carolee from Spokane Valley, WA
Really Easy
Less than 15 mins
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
Bottom part of refrigerator wasn't getting cold
1 personfound this instruction helpful.
Chad from RIDGEFIELD, NJ
Really Easy
30 - 60 mins
Pliers, Screw drivers, Socket set
$80 part motor fan replaced saved me $1000 or more on new fridge.
Called in and you guys helped out You guys are the best.
Was this helpful?
Thank you for voting!
freezer became frosty but refrigerator's camera didn'thave any coll at all.
1 personfound this instruction helpful.
Yakov from BROOKLYN, NY
Really Easy
30 - 60 mins
Screw drivers, Socket set
After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor. The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park.
... Read morer />As soon as I installed motor and turned on the refrigirator, everything start working properly. Thank you PartSelect, you sved me hundreds of dollars.
Read less
Was this helpful?
Thank you for voting!
no airflow to fresh food compartment or to freezer compartment....eveporator fan not working
1 personfound this instruction helpful.
Herbert from Pocono Lake, PA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Remove screws on the rear wall of the freezer. Pull the rear wall out and this gives you access to the evaporator fan assembley. Remove wires to the fan and to the defrost element to be able to move the rear wall to a position where you can work on the evaporator fan motor. The fan motor is held into place by a plastic bracket that c
... Read morelips onto the reverse side of the freezer rear wall. Careful not to break the plastic clips that hold the fan in place as they are brittle. The fan blade friction fits on to the fan motor shaft and is a little difficult to remove. Assemble in reverse order.
Cheap plastic part prone to break if crisper drawer jams even slightly.
1 personfound this instruction helpful.
Edward from SILVER SPRING, MD
Really Easy
30 - 60 mins
Nutdriver
After left side track broke 3 times and then center track also broke, I got tired of buying replacements (even though they are easy to install and not very expensive). So I bought a tube of plastic epoxy and a bit of fiberglass cloth and reinforced the plastic that the (#8 x 1/2 inch) screws go through (where it breaks) on ALL 3 tracks,
... Read morethen redrilled holes, added a washer, and used #8 x 5/8 inch screws). Maybe these wiil last.
Read less
Was this helpful?
Thank you for voting!
Not enough cold air in refrigerator
1 personfound this instruction helpful.
RICHARD from VENICE, FL
Easy
30 - 60 mins
Remove food from freezer shelf and ice maker back panel4 screws remove old motor replace with new motor reinstall all removed parts. Plug in and fan instantly came on refrigerator working great since
Was this helpful?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 peoplefound this instruction helpful.
Cathy from HOPATCONG, NJ
Very Easy
Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
light did not work on the refrigerator side
1 of 2 peoplefound this instruction helpful.
David from GROVESPRING, MO
Easy
Less than 15 mins
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i
... Read mores inside the refer!
My Orders
