install ice maker 2 screws wire harness pluged in done
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 peoplefound this instruction helpful.
Gail from Golden, CO
Really Easy
Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
replaced cracked compartment door
2 of 3 peoplefound this instruction helpful.
john from NORWOOD, MA
Really Easy
Less than 15 mins
removed old and installed new compartment door by hand.
Was this helpful?
Thank you for voting!
No cold
1 personfound this instruction helpful.
Jacqueline from LEXINGTON PK, MD
Very Easy
Less than 15 mins
Nutdriver, Pliers
Like you video
Was this helpful?
Thank you for voting!
3 screws
1 personfound this instruction helpful.
Michael from SALINA, KS
Very Easy
Less than 15 mins
Nutdriver
Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.
Was this helpful?
Thank you for voting!
Plugged it in.
1 personfound this instruction helpful.
Adam from GLOVERSVILLE, NY
Really Easy
Less than 15 mins
Nutdriver
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this helpful?
Thank you for voting!
freezer and refrigerator compartments not cold enough
1 personfound this instruction helpful.
Michael from Colorado Springs, CO
Really Easy
Less than 15 mins
Nutdriver
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this helpful?
Thank you for voting!
The Light Socket Burned Out.
5 of 13 peoplefound this instruction helpful.
MATTHEW from STOCKTON, CA
Really Easy
Less than 15 mins
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 peoplefound this instruction helpful.
Carolee from Spokane Valley, WA
Really Easy
Less than 15 mins
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
Not enough cold air in refrigerator
1 personfound this instruction helpful.
RICHARD from VENICE, FL
Easy
30 - 60 mins
Remove food from freezer shelf and ice maker back panel4 screws remove old motor replace with new motor reinstall all removed parts. Plug in and fan instantly came on refrigerator working great since
Was this helpful?
Thank you for voting!
freezer became frosty but refrigerator's camera didn'thave any coll at all.
1 personfound this instruction helpful.
Yakov from BROOKLYN, NY
Really Easy
30 - 60 mins
Screw drivers, Socket set
After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor. The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park.
... Read morer />As soon as I installed motor and turned on the refrigirator, everything start working properly. Thank you PartSelect, you sved me hundreds of dollars.
Read less
Was this helpful?
Thank you for voting!
no airflow to fresh food compartment or to freezer compartment....eveporator fan not working
1 personfound this instruction helpful.
Herbert from Pocono Lake, PA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Remove screws on the rear wall of the freezer. Pull the rear wall out and this gives you access to the evaporator fan assembley. Remove wires to the fan and to the defrost element to be able to move the rear wall to a position where you can work on the evaporator fan motor. The fan motor is held into place by a plastic bracket that c
... Read morelips onto the reverse side of the freezer rear wall. Careful not to break the plastic clips that hold the fan in place as they are brittle. The fan blade friction fits on to the fan motor shaft and is a little difficult to remove. Assemble in reverse order.
$80 part motor fan replaced saved me $1000 or more on new fridge.
Called in and you guys helped out You guys are the best.
Was this helpful?
Thank you for voting!
freezer would not freeze
1 personfound this instruction helpful.
Michael from HELENDALE, CA
A Bit Difficult
30 - 60 mins
Nutdriver, Screw drivers
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thic
... Read morek. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
My Orders
