Home
ART308FFDM08
Instructions

ART308FFDM08 Amana Refrigerator - Instructions

All Instructions for the ART308FFDM08

no airflow to fresh food compartment or to freezer compartment....eveporator fan not working

1 person found this instruction helpful.

Herbert from Pocono Lake, PA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers

Remove screws on the rear wall of the freezer. Pull the rear wall out and this gives you access to the evaporator fan assembley. Remove wires to the fan and to the defrost element to be able to move the rear wall to a position where you can work on the evaporator fan motor. The fan motor is held into place by a plastic bracket that c ... Read more

Read less

Other Parts Used:

Freezer Evaporator Fan Motor

Freezer Evaporator Fan Blade

Was this helpful?

Not enough cold air in refrigerator

1 person found this instruction helpful.

RICHARD from VENICE, FL
Easy
30 - 60 mins

Remove food from freezer shelf and ice maker back panel4 screws remove old motor replace with new motor reinstall all removed parts. Plug in and fan instantly came on refrigerator working great since

Was this helpful?

freezer became frosty but refrigerator's camera didn'thave any coll at all.

1 person found this instruction helpful.

Yakov from BROOKLYN, NY
Really Easy
30 - 60 mins
Screw drivers, Socket set

After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor.
The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park. ... Read more r />As soon as I installed motor and turned on the refrigirator, everything start working properly.
Thank you PartSelect, you sved me hundreds of dollars.
Read less

Was this helpful?

Thank you for voting!

Bottom part of refrigerator wasn't getting cold

1 person found this instruction helpful.

Chad from RIDGEFIELD, NJ

Really Easy

30 - 60 mins

Pliers, Screw drivers, Socket set

$80 part motor fan replaced saved me $1000 or more on new fridge.

Called in and you guys helped out
You guys are the best.

Was this helpful?

Thank you for voting!

Very easy installation

1 person found this instruction helpful.

David from Woodstock, IL

Really Easy

15 - 30 mins

Screw drivers

The cover just popped in, no problem

Other Parts Used:

Slide Rail - Left Side

Refrigerator Compartment Door

Was this helpful?

Thank you for voting!

compressor not running

1 person found this instruction helpful.

Doug from Lancaster, CA

Really Easy

15 - 30 mins

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

Was this helpful?

Thank you for voting!

freezer would not freeze

1 person found this instruction helpful.

Michael from HELENDALE, CA

A Bit Difficult

30 - 60 mins

Nutdriver, Screw drivers

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thic ... Read more k. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Read less

Was this helpful?

Thank you for voting!

Cheap plastic part prone to break if crisper drawer jams even slightly.

1 person found this instruction helpful.

Edward from SILVER SPRING, MD

Really Easy

30 - 60 mins

Nutdriver

After left side track broke 3 times and then center track also broke, I got tired of buying replacements (even though they are easy to install and not very expensive). So I bought a tube of plastic epoxy and a bit of fiberglass cloth and reinforced the plastic that the (#8 x 1/2 inch) screws go through (where it breaks) on ALL 3 tracks, ... Read more then redrilled holes, added a washer, and used #8 x 5/8 inch screws). Maybe these wiil last.
Read less

Was this helpful?

Thank you for voting!

light did not work on the refrigerator side

1 of 2 people found this instruction helpful.

David from GROVESPRING, MO

Easy

Less than 15 mins

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i ... Read more s inside the refer!
Read less

Was this helpful?

Thank you for voting!

Light switch broke off

1 of 2 people found this instruction helpful.

Kathy from TEMECULA, CA

Very Easy

Less than 15 mins

Pliers

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Was this helpful?

Thank you for voting!

Rocker on switch broke off

1 of 2 people found this instruction helpful.

David Barnes from ROSWELL, NM

Very Easy

Less than 15 mins

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Was this helpful?

Thank you for voting!

Doesn’t cool

1 of 3 people found this instruction helpful.

Benjamin from WASCO, CA

Very Easy

Less than 15 mins

Screw drivers

Work just perfect

Was this helpful?

Thank you for voting!

I broke the cooling fan while cleaning the heat exchange area

1 of 3 people found this instruction helpful.

Daniel from N TONAWANDA, NY

Really Easy

15 - 30 mins

Very simple, pulled old fan blade off and pushed new fan blade onto shaft. Perfect fit!

Was this helpful?

Thank you for voting!

light staying on

0 of 1 people found this instruction helpful.

Cecelia from Beaver Dam, WI

Easy

15 - 30 mins

Screw drivers

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

Was this helpful?

Thank you for voting!

Internal light did not come on each time the door was opened.

0 of 1 people found this instruction helpful.

John from Jefferson Hills, PA

Really Easy

Less than 15 mins

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical ... Read more outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Read less

Was this helpful?

Thank you for voting!

All Instructions for the ART308FFDM08

61 - 75 of 151
Prev
1
...
3
4
5
6
7
...
11
Next