Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The Light Socket Burned Out.
5 of 13 peoplefound this instruction helpful.
MATTHEW from STOCKTON, CA
Really Easy
Less than 15 mins
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 peoplefound this instruction helpful.
Carolee from Spokane Valley, WA
Really Easy
Less than 15 mins
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
freezer and refrigerator compartments not cold enough
1 personfound this instruction helpful.
Michael from Colorado Springs, CO
Really Easy
Less than 15 mins
Nutdriver
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this helpful?
Thank you for voting!
Installed Ice Maker in Freezer
1 personfound this instruction helpful.
Chris from SACRAMENTO, CA
Easy
1- 2 hours
Nutdriver, Screw drivers
Installed ice machine components using kit and included instructions. Easy! Ran a copper line from under sink valve to back of refrigerator under the floor. Drilled two holes to run copper line. Plumber turned water off and replaced single valve with a double valve (one line to faucet and the other for the copper line). Installed shut of
... Read moref valve and filter at the other end of copper line. Then stainless hose to refrigerator. Everything went smooth. Double check the factory installed plastic line from the electric valve to the inlet for your freezer. Mine was barely inserted and leaked. I pushed it in all the way and it is fine now... Ice maker works really well! Wish I had done this sooner!
Read less
Was this helpful?
Thank you for voting!
freezer became frosty but refrigerator's camera didn'thave any coll at all.
1 personfound this instruction helpful.
Yakov from BROOKLYN, NY
Really Easy
30 - 60 mins
Screw drivers, Socket set
After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor. The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park.
... Read morer />As soon as I installed motor and turned on the refrigirator, everything start working properly. Thank you PartSelect, you sved me hundreds of dollars.
Read less
Was this helpful?
Thank you for voting!
Cheap plastic part prone to break if crisper drawer jams even slightly.
1 personfound this instruction helpful.
Edward from SILVER SPRING, MD
Really Easy
30 - 60 mins
Nutdriver
After left side track broke 3 times and then center track also broke, I got tired of buying replacements (even though they are easy to install and not very expensive). So I bought a tube of plastic epoxy and a bit of fiberglass cloth and reinforced the plastic that the (#8 x 1/2 inch) screws go through (where it breaks) on ALL 3 tracks,
... Read morethen redrilled holes, added a washer, and used #8 x 5/8 inch screws). Maybe these wiil last.
Read less
Was this helpful?
Thank you for voting!
Bottom part of refrigerator wasn't getting cold
1 personfound this instruction helpful.
Chad from RIDGEFIELD, NJ
Really Easy
30 - 60 mins
Pliers, Screw drivers, Socket set
$80 part motor fan replaced saved me $1000 or more on new fridge.
Called in and you guys helped out You guys are the best.
Was this helpful?
Thank you for voting!
no airflow to fresh food compartment or to freezer compartment....eveporator fan not working
1 personfound this instruction helpful.
Herbert from Pocono Lake, PA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Remove screws on the rear wall of the freezer. Pull the rear wall out and this gives you access to the evaporator fan assembley. Remove wires to the fan and to the defrost element to be able to move the rear wall to a position where you can work on the evaporator fan motor. The fan motor is held into place by a plastic bracket that c
... Read morelips onto the reverse side of the freezer rear wall. Careful not to break the plastic clips that hold the fan in place as they are brittle. The fan blade friction fits on to the fan motor shaft and is a little difficult to remove. Assemble in reverse order.
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i
... Read mores inside the refer!
Read less
Was this helpful?
Thank you for voting!
Light switch broke off
1 of 2 peoplefound this instruction helpful.
Kathy from TEMECULA, CA
Very Easy
Less than 15 mins
Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
Rocker on switch broke off
1 of 2 peoplefound this instruction helpful.
David Barnes from ROSWELL, NM
Very Easy
Less than 15 mins
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this helpful?
Thank you for voting!
Doesn’t cool
1 of 3 peoplefound this instruction helpful.
Benjamin from WASCO, CA
Very Easy
Less than 15 mins
Screw drivers
Work just perfect
Was this helpful?
Thank you for voting!
I broke the cooling fan while cleaning the heat exchange area
1 of 3 peoplefound this instruction helpful.
Daniel from N TONAWANDA, NY
Really Easy
15 - 30 mins
Very simple, pulled old fan blade off and pushed new fan blade onto shaft. Perfect fit!
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 peoplefound this instruction helpful.
Ivanka from Atlantra, GA
Really Easy
30 - 60 mins
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read moret bulb in was not the problem.
My Orders
