Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No cold
1 personfound this instruction helpful.
Jacqueline from LEXINGTON PK, MD
Very Easy
Less than 15 mins
Nutdriver, Pliers
Like you video
Was this helpful?
Thank you for voting!
no airflow to fresh food compartment or to freezer compartment....eveporator fan not working
1 personfound this instruction helpful.
Herbert from Pocono Lake, PA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Remove screws on the rear wall of the freezer. Pull the rear wall out and this gives you access to the evaporator fan assembley. Remove wires to the fan and to the defrost element to be able to move the rear wall to a position where you can work on the evaporator fan motor. The fan motor is held into place by a plastic bracket that c
... Read morelips onto the reverse side of the freezer rear wall. Careful not to break the plastic clips that hold the fan in place as they are brittle. The fan blade friction fits on to the fan motor shaft and is a little difficult to remove. Assemble in reverse order.
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thic
... Read morek. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Read less
Was this helpful?
Thank you for voting!
freezer became frosty but refrigerator's camera didn'thave any coll at all.
1 personfound this instruction helpful.
Yakov from BROOKLYN, NY
Really Easy
30 - 60 mins
Screw drivers, Socket set
After describing my problem PartSelect consultant emmidiately diagnost the problem and I ordered Evaporator Fan Motor. Along with purches order confirmation I got video how to install a new motor. The hardest part was to connectthe ground wire becase space in that area was verylimited. Otherwise it was just like a walk in the park.
... Read morer />As soon as I installed motor and turned on the refrigirator, everything start working properly. Thank you PartSelect, you sved me hundreds of dollars.
Read less
Was this helpful?
Thank you for voting!
Bottom part of refrigerator wasn't getting cold
1 personfound this instruction helpful.
Chad from RIDGEFIELD, NJ
Really Easy
30 - 60 mins
Pliers, Screw drivers, Socket set
$80 part motor fan replaced saved me $1000 or more on new fridge.
Called in and you guys helped out You guys are the best.
Was this helpful?
Thank you for voting!
Not enough cold air in refrigerator
1 personfound this instruction helpful.
RICHARD from VENICE, FL
Easy
30 - 60 mins
Remove food from freezer shelf and ice maker back panel4 screws remove old motor replace with new motor reinstall all removed parts. Plug in and fan instantly came on refrigerator working great since
Was this helpful?
Thank you for voting!
Plugged it in.
1 personfound this instruction helpful.
Adam from GLOVERSVILLE, NY
Really Easy
Less than 15 mins
Nutdriver
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this helpful?
Thank you for voting!
Warm fridge and freezer but compressor was running. No air distribution inside fridge
1 personfound this instruction helpful.
Brian from BURTON, MI
Really Easy
15 - 30 mins
Nutdriver
I turned breaker off to fridge, it was easier than pulling fridge out in camper. I took 4 screws out of back panel that revealed the evap fan, took 2 more screws out to take fan bracket off. Unplugged fan plug. Took fan blade off the non working evap motor and put it on the new evap motor. Put all the screws back in the reverse orde
... Read morer and flipped the breaker and air started circulating.
Read less
Was this helpful?
Thank you for voting!
Fan was not spinning make it not cold in bottom part
1 personfound this instruction helpful.
Dylan from WHEELING, WV
Very Easy
Less than 15 mins
Screw drivers
Take screws out pull panel out unconnect the part connect new one and your done
Was this helpful?
Thank you for voting!
door hinge broke.
2 of 4 peoplefound this instruction helpful.
Bernard from DONALDSONVLLE, LA
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
Removed door and replaced bushing bracket was ok.
Was this helpful?
Thank you for voting!
compressor not running
1 personfound this instruction helpful.
Doug from Lancaster, CA
Really Easy
15 - 30 mins
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this helpful?
Thank you for voting!
Did not have ice maker
3 of 8 peoplefound this instruction helpful.
Marisa from TEMPE, AZ
Very Easy
1- 2 hours
Nutdriver
Followed online video instructions
Was this helpful?
Thank you for voting!
Light switch broke off
1 of 2 peoplefound this instruction helpful.
Kathy from TEMECULA, CA
Very Easy
Less than 15 mins
Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
Rocker on switch broke off
1 of 2 peoplefound this instruction helpful.
David Barnes from ROSWELL, NM
Very Easy
Less than 15 mins
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this helpful?
Thank you for voting!
light did not work on the refrigerator side
1 of 2 peoplefound this instruction helpful.
David from GROVESPRING, MO
Easy
Less than 15 mins
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i
... Read mores inside the refer!
My Orders
