ARS23 Amana Refrigerator - Instructions

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator i ... Read more n less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

Unplugged the machine removed the bottom plate and back plate and ice maker.Removed 2 wires to motor and ground wire.Removed 2 mounting nuts for motor,installed new motor and used old fan blade for new motor .Reinstalled in reverse order plugged in and tested fine.

First I removed the knobs, then the plastic cover over the thermostat. Then, I removed the two screws that hold it on. I removed the thermostat, unplugged the electrical leads, and pulled out the old thermostat. I then inserted the new one, hooked up the leads and reassembled.

I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered ... Read more the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.

turned water supply off, unhooked both set of
valves, reinstalled them, tested operation.
one valve on primary had to be capped also.

Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it ... Read more tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.

the problem was the evaporator has frozen causing the water line to freeze also.
I opened the cover to see the evaporator, verify it was frozen, try to unplug and let it thaw, but it would freeze again. Thought the defrost thermostat was not working but did not verify, order new one and replaced; it did not work. After a long time ... Read more of experimenting different things I found out that the defrost thermostat was supposed to be clamp to the line. It was not clamped to the line, was just hangin from its wires when I found it. So.....it works now!!! but I don't know what happen in the first place: the clamp fell off, or did it come from mgfr unclamped but happen to work since it was cold new, now getting old and not cold enough to close the thermostat unless on the line? anyway, it works and I decided to keep the part for spare. Hope this help someone else!

pull the fridge out away from the wall and hope you have a long flex water supply hose.remove cardboard cover,oh yea unplug fridge first.unplug wire from the relay.flip the wire retainer off the relay and pry it away from the compressor.pull the 2 prong capacitor off and then reverse the steps to reasemble. skip the middle man at the loc ... Read more al appliance shop.i waited 2 weeks for him to get the part and gave up.your reg shipping got it here in 2 days.

After doing some research it appeared that the water valve was the culprit. I don't have the expertise to test the old valve but I did try adding water manually to the icemaker and it spit out the cubes so I figured the icemaker itself was ok. I ordered the new water valve on a Friday morning and it was on my doorstep the next morning. ... Read more This was standard delivery!
I removed a few screws at the back of the refrigerator that holds the valve. Pulled the old one out, removed three hoses and two electrical connections. Reconnected the same on the new valve and reinstalled it. Later that day the ice cubes started dropping again.

Snapped the large end of the coupling onto the main line coming from the water source and snapped the other end onto the small line leading to the ice maker. Quick and simple.

Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit a ... Read more nd hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened th ... Read more e screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

First, I didn't know that my refrigerator water system even had a secondary water valve; I have replaced the primary water valve 3 times so far, and when that didn't fix the problem I looked further and there it was.

I turned off the water supply to the refrigerator and unplugged it, prior to working on it.

Then I t ... Read more ook the back panel off the 'frige with a cordless drill (the 1/4" hand nut drive was too slow), removed the primary water valve to get it out of the way, and remove the secondary water valve. all the electrical and tubing connections could be removed and installed by hand, so it was pretty easy.

The job duration could have been cut in half if my wife didn't make me clean behind the 'frige once I moved it....................

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

Removed two screws holding valve, removed two 1/4" water lines. disconnected wire clip from old valve.
Installed new valve, connecting water and electrical with ease.
Absolutely Simple!