ARR60 Amana Range - Instructions

Removed screws holding rear cover, removed cover. Male connector on Broil Element had rusted off and caused wire to fall onto the frame of the range, shorting it out.

Removed element by disconnecting other wire and removing the single Phillips head screw accessible from inside the oven. Released the element from the two hook ... Read more s towards the front of the oven near the door and removed.

The wire to the element that burned off had a high temperature female push on connector that I did not have on hand. I had a high temp ring connector so I drilled one of the male connectors on the new element so I could use a small stainless screw and nut which I had to hold the ring terminal on.

After crimping the new connector on I fastened it to the element, connected the other wire and put the rear cover back.

Good to go now!

The repair went real easy. Turned off power, unscrewed two screws at back of oven and disconnected the two wires. Reconnected two wires to new broiler element and remounted the new one with the two screws. Turned the breaker back on and had a steak cooking in no time.

This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Shut off power to the oven.
Unscrewed the old broiler element, unplugged it.
plugged in new one, screwed it in.
Turned on the power. Voila!

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!

I reoved old drip pans and installed new ones. Very easy, they look great!

After receiving the part I was able to quickly remove the old piece and replace with the new. For this project you have to remove the back of the oven to remove the electrical attachments.

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked ... Read more . Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

I had My friend from church come over and look at the problem. He said that it could be fixed, so he looked up the part and ordered the part. It came in two days, it took about 15 minutes to install the part and put the back back on. It was that easy! Thank you! Now i don't have to buy a new stove!!

Drilled a pilot hole with a 1/16 th drill bit and tapped off screw head.

Oven was missing the broiler element when I moved in so the connector/wires to plug the broiler were no longer visable in the main part of the oven (otherwise the repair would take 2 minutes). Moved oven away from wall and unplugged. Unscrewed sheet metal on the back of oven and found the broiler wires (the only two NOT connected to somet ... Read more hing). Fed the wires back into the oven and plugged in the broiler. Attached the broilers to the top hooks. Put sheet metal back on. Everything worked fine. I wouldn't say I know much about fixing things, but this was a very straight-forward job.