My Orders
ARGS7650W Amana Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Missing oven rack
2 of 3 people
found this instruction helpful.
-
Denise from Pittsburgh, PA
- Really Easy
- Less than 15 mins
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You
Was this helpful?
Thank you for voting!
Cosmetic replacement of stove top burner bowls.
3 of 6 people
found this instruction helpful.
-
Larry from Owensboro, KY
- Really Easy
- Less than 15 mins
Easily replaced the stovetop burner bowls by removing the old ones and replacing with the new ones.
Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!
Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!
Was this helpful?
Thank you for voting!
Oven glass imploded during use.
2 of 3 people
found this instruction helpful.
-
Vidanand from Rochester, NY
- Easy
- 30 - 60 mins
-
Screw drivers
Removed oven door by pulling off of hinges. Then removed screws that held door frame together. Replaced glass. Reassembled.
Was this helpful?
Thank you for voting!
Broiler inoperative
2 of 3 people
found this instruction helpful.
-
Donald from East Syracuse, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire
... Read more
within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.
Read less
Was this helpful?
Thank you for voting!
Our oven was very slow lighting (would sometimes take over 30 minutes)
1 person
found this instruction helpful.
-
Richard from Greenville, NC
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in secti
... Read more
on, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!
Read less
Was this helpful?
Thank you for voting!
Broken inner glass in oven door
1 person
found this instruction helpful.
-
Scott from Bay Village, OH
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Removed screws on edges of door. Romove front panel. Remove several screws around glass. Replace inner glass and replace screws. A little tricky reinstalling trim around door front.
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person
found this instruction helpful.
-
Timothy from Madison, AL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove. ... Read more r />Needed flashlight to see under stove.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove. ... Read more r />Needed flashlight to see under stove.
Read less
Was this helpful?
Thank you for voting!
Gas oven would not light
1 person
found this instruction helpful.
-
Elizabeth from Vernon, CT
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I have an older model gas oven which required that all screws had to be removed. With a screw gun the job would not haven taken long. Once the bottom pan was removed the oven ignitor took some finese to remove. This was only due to the short wires. Once pulled sufficiently to be able to disconnect the ignitior (although I was afraid I
... Read more
was going to pull the wires and separate them from the stove), it was very simple to unplug and plug in the new one (again, making sure to hold the plug so the wires would not retract back behind the wall which would have required the stove to be pulled out from the wall and the back disassembled).
The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.
The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.
Read less
Was this helpful?
Thank you for voting!
The oven would take 45 minutes to over an hour to preheat.
1 person
found this instruction helpful.
-
Timothy from Elk Grove Village, IL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I removed the oven door by removing two screws, one above each hinge. With the door screws removed, position the door to the slightly open position and lift strength up to remove. Remove wire racks and the cover from the bottom of the oven. Remove the heat deflector which is held on with a single nut. Remove the screws that hold the cavit
... Read more
y that houses the igniter and the burner. The igniter is held in place by a protective bracket that has to be reused. I slid the old igniter out of the protective bracket and then removed the cavity by allowing the burner and igniter to exit through an opening in the rear of the cavity. The drawer (broiler pan storage) had to be removed to remove the two screws to an access panel that allowed access to the igniter connector. After disconnecting the old igniter, I fished the new igniter connector through the back of the oven to connect it. I use masking tape to hold the access panel in place while reinserting and tightening the two screws. Replace the cavity that houses the igniter and burner. Slide the protective cover over the igniter. Realign and secure the burn and igniter assembly by reinserting and tightening the necessary screws. Reinserting and tighten the screws around the igniter/burner cavity. Replace the heat deflector by tightening the nut. Replace the cover that covers the bottom of the oven and the wire racks. Reinsert the drawer. Slide the door over the hinges and reinsert and tighten the two screws.
Read less
Was this helpful?
Thank you for voting!
Gas oven would not heat up
1 person
found this instruction helpful.
-
John from Blairsville, GA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
My repairman told me it was probably the ignitor (even though the old one sitll glowed), but after weeks of waiting for his back-ordered part, I decided to try it myself - found it on PartSelect and had it 3 days later. Turned off the power to the oven. Slid out the 2 racks, and the cover below the racks. Unscrewed 1 nut and removed th
... Read more
e V shaped metal plate that distributes the heat. Under that removed 3 screws that hold the ignitor clip in place and got the igniter out of the clip. I couldn't get to the plug on the other end of the ignitor until I took out the oven drawer and removed 2 screws holding a metal cover in place below the oven. Reversed the whole process being careful with the end of the new ignitor (I read it was fragile). The oven now heats up in 5 minutes and maintains temperature again!
Read less
Was this helpful?
Thank you for voting!
old igniter would not light stove
1 person
found this instruction helpful.
-
Carlos from EAST NEWARK, NJ
- Really Easy
- 30 - 60 mins
Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter
Was this helpful?
Thank you for voting!
NO Work.
1 person
found this instruction helpful.
-
Robert J. from WESTMINSTER, MD
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC
Was this helpful?
Thank you for voting!
Oven would not light, even though the ignitor looked as though it was working, the slightest crack affects the resistence and the signal to send gas does not work.
1 person
found this instruction helpful.
-
WILLIAM from BENSALEM, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
It was Tuesday before thanksgiving, panic as there was a big bird looking for a hot stove,
unplug stove from its electrical supply
turn off gas, not necessary but sometimes it's good to be safe.
inside oven remove bottom splash cover "pull towards you and lift out, then remove flame pan, one nut in the center, remove and l ... Read more ift out flame pan.
The oven ignitor was to the left of the burner, with 3 philips screws one attached to buner and the other two to the back of the stove, remove all three.
The ignitor is now loose,
remove bottom drawer and behind is a plate attched to the back of the stove with two screw, the screws are facing you as you look in where the drawer was, remove screws and plate to access the plug attatching the ignitor to its power supply .
go back to the oven and remove ignitor.
install new, feed plug through back, and put it all back together.
"ignitor very delicate, handle with care"
I am also not the biggest of guys and it can be awkward getting in the drawer space as you need both hands to plug it back in, so tilting the stove back, keeping safety in your thoughts at all times, would be a must for most people.
unplug stove from its electrical supply
turn off gas, not necessary but sometimes it's good to be safe.
inside oven remove bottom splash cover "pull towards you and lift out, then remove flame pan, one nut in the center, remove and l ... Read more ift out flame pan.
The oven ignitor was to the left of the burner, with 3 philips screws one attached to buner and the other two to the back of the stove, remove all three.
The ignitor is now loose,
remove bottom drawer and behind is a plate attched to the back of the stove with two screw, the screws are facing you as you look in where the drawer was, remove screws and plate to access the plug attatching the ignitor to its power supply .
go back to the oven and remove ignitor.
install new, feed plug through back, and put it all back together.
"ignitor very delicate, handle with care"
I am also not the biggest of guys and it can be awkward getting in the drawer space as you need both hands to plug it back in, so tilting the stove back, keeping safety in your thoughts at all times, would be a must for most people.
Read less
Was this helpful?
Thank you for voting!
Oven doesn't start
1 person
found this instruction helpful.
-
Dennis from STEWARTVILLE, MN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Installed new igniter - easy job. Remove burner deflector, remove screws holding igniter bracket, remove panels below oven (accessible via removal of drawer), disconnect igniter and remove. Remove igniter from bracket, slide new one into bracket and reverse the steps to install it. Unfortunately, it didn't work. Igniter not glowing.
... Read more
I checked continuity on the igniter and it showed 90ohms resistance, so seems to be OK. Put multimeter on range plug end, turned on oven and multimeter did show cycling voltage at the plug (although I'm not certain what it should read). Relay in the control board does 'click' when oven turned on, so it also seems to work. Think I may be down to the gas control safety valve for the oven, but it is no longer available. Anyone have any other ideas? Hate to buy another igniter and have it still not work. Thanks!!
Read less
Was this helpful?
Thank you for voting!
Oven would not light
1 person
found this instruction helpful.
-
Daniel from NAPERVILLE, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Removed old ignightor and installed new one
Was this helpful?
Thank you for voting!