ARGS7650E Amana Range - Instructions

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires ... Read more in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy ... Read more repair,

Removed the oven racks for room to work.
Removed a protective cover (slide forward, lift up).
Remove winged cover plate.
See igniter assembly.
Remove 2 or 3 holding screws (I don't want to go in and count them - it's obvious - they are clearly in view - get a good screw-driver seating - they come out easily).
The ... Read more igniter assembly is then loose and ready to com out.
Remove the stove drawer to get at the access plate at the rear - comes off easily(the wires to the igniter were then clearly identifiable).
Release the wire plug - I marked one side with a sharpy - polarity of fit, not voltage.
Gently feed the igniter assembly out the bottom using the wires.
Remove the igniter from the shroud (may have to pul it apart a little - it's tight - it does come out easily after prying the shroud a little - mark a side with a sharpy - for mechanical orientation.
The part number should be on the igniter.
I did not bother matching the part number.
Just matched the stove brand and model.
The parts diagram provided by PartSelect was invaluable.
I put an ac meter up the holes of the plug (stove side, of course) turned on the stove to see the meter measure 115vac - assurance that the igniter was bad and not anything else.
Just reverse the removal process.
Just takes a little time and patience.
Very very doable.
Good luck.

Replaced glow bar/ igniter.

First, I removed the oven door (two screws and pulled it off the hinges) and placed it out of the way. Then I removed the baking racks and bottom cover over the heating element this exposed the heating element, easily removed (two screws). I unplugged the old element, plugged the new element in, and put all the stuff back and the put ... Read more the door back on. Next was the fun part. . . Had to get the wife to turn on the oven (very complicated touch pad - not made for a man to understand), and shazamm the oven came on! Now I can have some of those great homemade biscuits again!

Removed oven racks and bottom cover plate. Removed stainless steel diffuser to access igniter. Removed bottom storage drawer and unplugged connector for igniter. Removed defective igniter by by taking out 3 screws holding stainless steel mounting bracket in place. New replacement part had totally different bracket which prevented it from ... Read more mounting in the proper orientation so I carefully removed defective igniter from original bracket and installed new igniter. New part was tacked in place by some sort of high temp adhesive that had to be carefully removed to allow it to be installed in old mounting bracket. Installed new assembly in the oven and when I tried plugging in the power connector I discovered the pins on the new igniter were the wrong sex; both sides had male pins! Removed igniter again and cut off the two pin connector and installed a brand new 2 pin molex type connector. I installed a mating connector on the original length of wire and connector that I cut from the defective igniter along with the heavy insulating material so I now had a properly mating set of connectors. Went through the mounting process again; successful mating this time. Oven lights in 50 seconds. If it dies again I'll have a connector of each
sex ready before repair.

I pulled the ckt breaker, removed the oven drawer and disconnected the igniter. I opened the oven door and unscrewed the igniter holding bracket and removed the bracket and igniter. I broke the old igniter element when removing it from the bracket. When installing the new igniter in the holding bracket I broke the ceramic element. REALLY ... Read more BE CAREFUL. Ordered a new igniter, very carefully installed it in the bracket, then rversed the removal process. It's not hard, you just have to be careful

Bought a new one. . Three years later =)

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carr ... Read more ied back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

Removed oven grills and top of burner pan. This exposed the igniter. Removed 3 phillips head screws from igniter bracket. Slid old igniter out the back end. Removed utility drawer. Removed two screws from back pan covering igniter plug-in. Unplugged igniter, removed from range. Handling of igniter is tricky..do not touch black end. Slide ... Read more new igniter into the bracket, feed wire with connector through hole in back (where igniter was removed from), install the three screws for the bracket (your new igniter is now secure), from the bottom, plug in the new connector it only goes on one way. Re-install pan with two screws. Put utility drawer back in..job is complete!!

I pulled the racks out of the oven. Then pull the plate off that covers the burner. There is another shield with a nut on it that covers the burner. Removed it.
The ignitor is mounted on the back of the burner, held by 3 screws, remove them. Pull the bottom sliding drawer out completely. (you have to lay down for this). There is ... Read more a metal plate in the very back held with 2 screws, remove them and pull the plate out. You'll see the 2 high temp wires (White) with a plug connector, simply unplug the connector and you are ready to pull the whole ignitor assembly off the burner. The ignitor ceramic base simply slides out of the sleeve.
Put the new ignitor in the sleeve and put everything back together. It's pretty simple.
This is the second ignitor I have installed in 2 years, hopefully I'll get more life out of this one.
Good Luck.

very simple repair, the oven had the issue about ten years ago, just removed drawer ,removed two screws holding cover plate unhooked power and disconected plug. removed element screws and pulled out old element from holder and inserted new one. re attatched element holder, cover plate, and put drawer back in. works great !!!
My part ... Read more s wrere shipped promptly and arraived in great condition, stove looks and works like new again

I had changed the broiler igniter several years ago, but it had "burned out". The only thing that slowed me down on this repair was that the igniter was glowing brightly, but the oven would still not ignite. Others have written that it's best to try a new igniter FIRST. That indeed was the solution.

One "trick" that I did ... Read more not find in other posts was how to get to the plug on the end of the igniter - so here's how.

First, open the oven, remove all racks and the bottom cover. Remove the nut holding the heat deflector in place and remove the heat deflector. Then remove the three screws holding the igniter in place.

Second, pull out the bottom drawer of the ove and remove it. At the very back there is a sheet metal cover held in place by two additional screws; remove them to rermove the sheet metal cover - this will allow access to the plug on the other end of the igniter. Unplug the igniter.

Third, feed the plug end of the new igniter from inside of the oven to the underside. Plug it in, reattach the sheet metal cover, reinstall the drawer, screw in the new igniter and put the heat deflector back in place.

Note of caution: be careful handling the igniter - it's fragile and easily broken.

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

diagram on website was very helpful. simply unscrew two screws,remove and replace electrode and works perfectly.
Ordered one day arrived next with standard shipping installed before next day supper awesome service