ARG7800S Amana Range - Instructions

After reading previous posts regarding this type of problem, I determined the very high likelyhood that the over ignitor needed to be replaced. Accessing the underneath of the oven compartment, I removed the metal shield covering the ignitor wires in order to unplug the ignitor. (Be sure to disconnect power cord first)
From inside of ... Read more the oven compartment remove the flame spreader plate ( 1-screw) which gives access to the ignitor. Remove the three screws holding the ignitor bracket and pull the wire and plug through. That's it !!
Installation of the new ignitor is the reverse of the above proceedure.
Oven now functions normally again.
A very simple repair.

This was VERY easy and I've never worked on this type of appliance before.

First, take off the grate, thermal plate, etc that are resting on top of the stove (this is all the stuff you take off to clean the stovetop).

Then, carefully unscrew the two screws holding the burner to the gas pipe. Grab the screws and set ... Read more them aside so they don't fall back into the stove, then pick the burner up off the stove.

once you have the burner a few inches above the stove surface, wiggle off the single wire by grabbing it on the metal part (not by the wire) and gently wiggling it off.

Grab new burner, push on wire and sit it on stove, use a finger in the gas pipe to align it and put the two screws in. you're done.

cleaned out pad area with an awl. then the pads just slide in.

Removed the door and old hinges and reinstalled the new hinges and added some screws to better support the door ( it was bending a little at the middle and the door would not shut all the way. Now it works fine.

Had to take entire back panel off, to disconnect wiring. Once disconnected, removed two screws holding up igniter in oven. Pulled it through and removed from holder, Be careful new igniter very fragile. Reconnected, put panel back on, then turn on to verify, all went well, fully operational.

I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all t ... Read more ogether. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.

I read on this site about someone who had my same problem. He ordered and installed a new spark ignition module and after installation the stove worked fine. So I ordered a part # PS2034431 Spark Ignition Module for my Amana stove. I installed it, and it worked just fine, really for the first time since I bought the stove new. Oh well ... Read more ...
Taking the stove apart took a bit of study to find how to get it right, and the clothes pins were to keep the wires from slipping back through the stove top as I was putting it back on before actually hooking up the piezo units. The instructions that came with the spark igniter were pretty useless (not wrong, just useless), but carefull notes while taking the bad unit out and where each wire went made the replacement rather easy. The really tough part was removal of the burners - the small screws had deteriorated over the last 7 years, so I had to drill two of them out. I replaced all of them with stainless steel screws. This cost an hour of my time plus a trip to the hardware store.
But as I said... the stove now works fine really for the first time. Way to go, Amana!
I trust this igniter will last a lifetime.
And certainly, reading about the same problem I had and easily finding the part was a welcome treat on this site.

opened up the oven to locate the position of igniter

disconnected igniter and checked the continuity of the igniter to find that I had an open circuit

once I found out the igniter was no good I google for appliance parts and found parts select had the best prices that I could find. I called a couple local parts st ... Read more ores and there prices were definately inflated. I chose to go with parts.select.com
I receive the part in two days! I installed the new part within 15 minutes and turn on the oven to have it light almost instantly. I won much praise from my wife. Parts.select.com recieves my praise for ease and quickness of part delivery.

left side hinge was broken. I removed 2 screws to release the old hinge and replaced it with the new hinge.
Part select.com made it easy to pick out the part from the diagram supplied on the web site. After it was ordered it arrived 2 days later.

I took out ruined racks. Cleaned the oven, getting rid of all the melted plastic. Once oven was sparkling clean, I slid in the new racks I bought from here. (The easiest part).

* * * *
I'm very thankful to have found this site. My oven has been "out of order" for over 3 years. It's so nice to be able to use it again! =)

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just ... Read more 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

A Home Depot employee advised me on how to enter all my oven information found on the front of my oven on parts.com. I submitted parts information as stated, also very easy. My parts arrived 3 days later. I used a screwdriver & pliers, it took less than 15 minutes. Very simple and the entire process from order to installation went like cl ... Read more ockwork. I would definitely order in the future. Thank you.

Repair can be done through the oven after removing the dip pan on top of the oven burner. The drip pan slids out - no tools needed. Remove 1 screw that holds the element close to the burner and 2 screws that hold the element cover to the stove. Remove bottom drawer and remove wire nuts from element wires. Reverse the process to install ne ... Read more w element. Care must be taken to avoid damage to the element as it can be easily broken. I cut and stripped the wires coming from the stove valve as they were not in good shape after removing the wire nut.

Removed the two screws that hold the element in place. Disconnected the wire to the electrode. The screw holding the electrode to the burner plate would not unscrew so I had to drill out the screw in order to replace it with the new ignition electrode. A little more time involved but if the screw would have come out it would have been a ... Read more 10 minute job.When I ordered the part from you it came very quickly and I will certainly use you again when I have any other issues.

First turn off power to stove with breaker or unplug it. Then remove three screws under the front of cook top, and lifted up cook top from the front. Then brace it up with a stick about 20 inches long so you can work. Now locate the latch at the front of range. Next get some paper and labeled where each wire is connected by color. Remove ... Read more wires from old part, next take out two screws by the front of part. Remove a clip on left side of part that is holding the wires. Take old part out and replace with new part, put back the two screws in front of part. Next put the wires back on using the list you made. Then replace clip to hold wires. Now turn power back on,or plug it back in. Reset clock and your done.