ARG7600L Amana Range - Instructions

Subject range is in a rental house and receives much use and abuse. The repair was necessary due to the door having 2, 1-2 inch cracks one on each side so the door bent outward. Obviously in the past when the oven door was completely in the open position much weight was placed on the door cracking the sides and bending the door. Consequ ... Read more ently, when the oven was in use and the door was closed being that the door was bent outward heat escaped from the top of the door heating up the control panel. The control panel would get so hot that it could not be touched without burning the fingers. Replacing this range would cost approximately $2200, so we had to try to repair it. I went to the ParSelect website and ordered the part I needed.
Being that the oven door is heavy and large it took two people to disassemble and reassemble the door. We had quite
a wrestling match with the door (consider too, that we never do this type of job) but after about 3 hours our range was almost like new.
Disappointing that a replacement mylar cover for the control panel is no longer available at PartSelect. We would appreciate getting our hands on one as the existing mylar cover is cracked.
The oven has been successfully used since the repair and we have a good fit and the control panel is now only warm instead of blistering hot. FANTASTIC!
THANK YOU


Time will tell.

Sincerely

Craig and Judy Crouch

i read other stories and found after checking rotating heat switch with ohm meter found the igniter was the problem, pulled up on door and it came off, found bottom of oven pulled up and out, removed wing nut from deflector and two bolts and one wiring connector, just reversed removal to install new igniter and all complete, took about ... Read more 20 minutes,

First, I unplugged power to the stove. Next, I removed the grills, ceramic burner discs, gas knobs, and glass plate (under the knobs). Next, I removed the 2 screws exposed by the control knobs. Next, I removed the 2 screws holding each burner assembly to the cook top. I then unplugged the wires attached to each burner assembly and set th ... Read more e assemblies aside. Now I was able to remove the top. Once removed, it was very easy to locate and remove the bracket holding the old sparking module. Then it was just a matter of removing the wires from the old module and attaching them to the new module... attaching the new bracket to the stove and then re-assemble the cook top. Honestly, this was a very simple repair... and probably took me longer to describe the steps than actually execute.

I took out the oven racks. There are 2 cross head screws and 1 screw with a hex head holding the igniter. Pulling out the igniter carefully and the wire nuts also came out. Replaced the wires using the existing wirenuts and slid the igniter into place. Replaced the 3 screws and DONE. Wish the igniters were a little cheaper as this is th ... Read more e third one to go weak. The new one draws about 3.2 amps while the old one only drew 2.85Amps, not enough to open the gas valve. Oven works Fine now. Thanks parts select for the rapid delivery.

Philips is all that's needed. Remove the burners (2 screws each) lift off top of stove, replace the ignition module. put all back together and your done. Local parts store wanted $80+ for the module. PartSelect only $50 total cost and it hit my mailbox in TWO days! Thank you PartSelect.

i had to remove quite a lot of screws in the bottom "pan" of the over to get to the igniter wiring. once it was apart, it was easy to see how to disconnect and reconnect the new igniter. the trickiest part is to put the igniter into the metal sheeted housing before you try to thread the wiring through to the plug at the back of the stov ... Read more e. overall, this is an easy rip out and replace process.

Removed two screws per burner. Unhook wires. Putting back broke slide on connector and had to replace. That took longer than the whole job. I ordered the part before 3:00 pm and it was at my house tjhe next morning which was hard to believe. The instructions that come with part made no sense what so ever. Thanks for the quick service and ... Read more I will be back.
Dave

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest ... Read more that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.

Removed oven door. Removed three screws on ignitor holding bracket. Pulled out the range from the wall and reached underneath to access the wire nuts on the wires. Removed old ignitor and replaced with new one. Reconnected wires and then and replaced bracket and that's it. Works great now.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

First I removed the two screw on the lower inside of the door that hold the door to the hinges. Then I opened the oven door at about a 15 degree angle, and carefully lifted the door out of the hinge brackets. Next I had to remove the side panels on the door . After getting those side pieces off, I realized that I had to go through all ... Read more layers of the door to get to the inner glass, so I decided that the best way to keep track of all those screws, was to remove each screw with the Phillips head screw driver, and immediately scotch tape that screw right next to the hole it came from. That was the best idea I had, because there are many screws in that door! Removing the old glass, and replacing it with the new glass was the easiest part of the project, just be sure not to let pieces of the insulation get between the glass and the metal frame. Then I reversed my steps to put everything back together. It probably took a bit longer than someone else because I first taped each screw on the panels, and then had to remove the tape, but I just did not want to find a handful of screws after the door was back on, or worse, somehow lose one or two. I think the hardest part of this project was getting the door back on the hinges, because the door is heavy, and you have to line up the hinges with holes in door, and slide the door in evenly. Once the door is back on, re-insert the two screws, and your oven door is as good as new (and as clean as new).

Symptoms were sign of bad ignitor based on Goggle searches. Removed screws holding burner and ignitor to range. Disconnected ignitor at green connector below oven with lower drawer removed. Then removed burner and old ignitor. Reinstalled burner and then new ignitor being sure burner was still seated on gas outlet. (Note-burner removal ma ... Read more y not be necessary) Replaced two screws attaching ignitor to oven wall and two screws attaching burner to floor of oven. Oven works perfectly now.