ARG7600C Amana Range - Instructions

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back ... Read more on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Unplugged the stove, removed all 4 burner discs from the stove top (2 screws each- WATCH YOU DONT STRIP HEADS) and disconnecting electrode wires ( DONT HAVE TO- IF YOU HAVE ENOUGH ROOM TO SIDE TOP UNIT OVER), unscrewed the old module, removed each of the 6 wires,one at a time and connected wires to the new module. Plug in stove to test be ... Read more fore you screwed it into place, reinstalled the top unit , put the stove top in place,. Done!

remove knobs and 2 screws from front panel, remove front panel. remove burner grates and caps. remove 8 screws (2 per burner base). remove each base and unplug wire. remove the top of the range. locate an remove old ingition module with bracket. on my model i did not need the new bracket. the new module fit right in the old one. unplug w ... Read more ires from old module and plug them into the new one in the same place they were in the old one. reverse the order to reassemble. new module does not make the same clikcing noise (not as fast as old one), but it lights on the first click. GRERT JOB PARTSELECT.!!! parts go to my house within 2 days...saved about $40-$50.

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires ... Read more in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

Removed the oven racks for room to work.
Removed a protective cover (slide forward, lift up).
Remove winged cover plate.
See igniter assembly.
Remove 2 or 3 holding screws (I don't want to go in and count them - it's obvious - they are clearly in view - get a good screw-driver seating - they come out easily).
The ... Read more igniter assembly is then loose and ready to com out.
Remove the stove drawer to get at the access plate at the rear - comes off easily(the wires to the igniter were then clearly identifiable).
Release the wire plug - I marked one side with a sharpy - polarity of fit, not voltage.
Gently feed the igniter assembly out the bottom using the wires.
Remove the igniter from the shroud (may have to pul it apart a little - it's tight - it does come out easily after prying the shroud a little - mark a side with a sharpy - for mechanical orientation.
The part number should be on the igniter.
I did not bother matching the part number.
Just matched the stove brand and model.
The parts diagram provided by PartSelect was invaluable.
I put an ac meter up the holes of the plug (stove side, of course) turned on the stove to see the meter measure 115vac - assurance that the igniter was bad and not anything else.
Just reverse the removal process.
Just takes a little time and patience.
Very very doable.
Good luck.

I removed the ignitor.
Ordered the matching part.
4 days later the part arrived and I installed the part.

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy ... Read more repair,

Removed the three screws holding the igniter, pulled the old one out and plugged in the new one. Very simple.

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carr ... Read more ied back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

diagram on website was very helpful. simply unscrew two screws,remove and replace electrode and works perfectly.
Ordered one day arrived next with standard shipping installed before next day supper awesome service

The repair was fairly straightforward. The drawer below the oven had to be pulled out and the panel in the rear (looking from the front through the opening where the drawer was) was removed. It was then a matter of removing two screws and unsnapping the wire connection. And then replacing the igniter.

ordered new broiler pan

I pulled the racks out of the oven. Then pull the plate off that covers the burner. There is another shield with a nut on it that covers the burner. Removed it.
The ignitor is mounted on the back of the burner, held by 3 screws, remove them. Pull the bottom sliding drawer out completely. (you have to lay down for this). There is ... Read more a metal plate in the very back held with 2 screws, remove them and pull the plate out. You'll see the 2 high temp wires (White) with a plug connector, simply unplug the connector and you are ready to pull the whole ignitor assembly off the burner. The ignitor ceramic base simply slides out of the sleeve.
Put the new ignitor in the sleeve and put everything back together. It's pretty simple.
This is the second ignitor I have installed in 2 years, hopefully I'll get more life out of this one.
Good Luck.

Removed oven grills and top of burner pan. This exposed the igniter. Removed 3 phillips head screws from igniter bracket. Slid old igniter out the back end. Removed utility drawer. Removed two screws from back pan covering igniter plug-in. Unplugged igniter, removed from range. Handling of igniter is tricky..do not touch black end. Slide ... Read more new igniter into the bracket, feed wire with connector through hole in back (where igniter was removed from), install the three screws for the bracket (your new igniter is now secure), from the bottom, plug in the new connector it only goes on one way. Re-install pan with two screws. Put utility drawer back in..job is complete!!

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!