ARG7301 Amana Range - Instructions

Philips is all that's needed. Remove the burners (2 screws each) lift off top of stove, replace the ignition module. put all back together and your done. Local parts store wanted $80+ for the module. PartSelect only $50 total cost and it hit my mailbox in TWO days! Thank you PartSelect.

Removed two screws per burner. Unhook wires. Putting back broke slide on connector and had to replace. That took longer than the whole job. I ordered the part before 3:00 pm and it was at my house tjhe next morning which was hard to believe. The instructions that come with part made no sense what so ever. Thanks for the quick service and ... Read more I will be back.
Dave

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest ... Read more that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

Removed oven door. Removed three screws on ignitor holding bracket. Pulled out the range from the wall and reached underneath to access the wire nuts on the wires. Removed old ignitor and replaced with new one. Reconnected wires and then and replaced bracket and that's it. Works great now.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.

Symptoms were sign of bad ignitor based on Goggle searches. Removed screws holding burner and ignitor to range. Disconnected ignitor at green connector below oven with lower drawer removed. Then removed burner and old ignitor. Reinstalled burner and then new ignitor being sure burner was still seated on gas outlet. (Note-burner removal ma ... Read more y not be necessary) Replaced two screws attaching ignitor to oven wall and two screws attaching burner to floor of oven. Oven works perfectly now.

I replaced the Oven Igniter. With a ohmn meter I checked the resistance on the Igniter and there was nothing there. I figured the module had to see some kind of resistance to turn the gas on. The Oven now works after replacing the Oven Igniter, but the Broiler still will not light. I will check the resistance on the Broiler Igniter an ... Read more d see what is going on there.
The Igniter can be checked from the back by removing the back cover panels. The two igniter wires come out through the back of the oven and have heat resistant covering on them. They run into a plastic plug and can be accessed at this point to check the resistance.
To remove the Oven Igniter, remove the oven racks, the bottom panels which are held on by screws. The Oven Igniter is attached to the gas rail which is attached to the underside of 2nd panel by two wing nuts.

I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.

No problem removing the burners. Removing the old initors was a different story. The tiny screws that hold the ignitor in place were baked in and could not be removed with a screw driver. I drilled them and tried to use an easy out to no avail. The screws are very short so I had to use care not to drill thru the burner. Both screw heads d ... Read more id snap off. I resorted to a hi temp epoxy to secure the ignitor flanges to the burner and now the all burners ignite as designed.

The earlier reviews said very easy and 15 minutes for beginners. They were right on, except I could not get the old screw out no matter what I tried. I eventually had to drill it out and put in a self tapping new screw. This was a first for me. Then it took 15 minutes or less and works fine again. Hopefully next time someone will tell me ... Read more how to get that old screw out faster.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I removed the cartridge from the range and used a screw driver to remove the screws holding the burners assembly in the housing. (Some prefer to remove the burner from the top by removing the two screws, but I've had trouble realigning the parts that way.) I removed the ignition wire and the screw holding the bad electrode in the burner ... Read more . I then installed the new electrode, attached the ignition wire, put the burners assembly back into the housing, and put the housing back into the range.