ARG7300 Amana Range - Instructions

Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.

Unscrewed the burners,lifted the top up,unplugged the burners.Took out the bad module,making sure of where the wires went and put them in the same spots on the new module,reconnected the burners lowered the top screwed the burners back in and the burners lit.

I went ahead with the repair after reading how easy it was. I located the wires which were spliced, held together with wire nuts and wrapped in black insulation tape which did not feel right. Not realizing that these were ceramic heat resistant wire nuts and not wanting to cut the connector off the new ignitor I tried in vain to find a wa ... Read more y to disconnect the original from it's source. In vain I searched for a way to reach where it plugged in. Looking for diagrams on line I came across one mention of: when you can't reach where to unplug the connector splice the wires using the heat resistant wire nuts. Encouraged I did that without the black insulation tape and then tried to slide the ignitor into the protective housing. The filament broke! I was devastated. Out $50.00 plus ego deflated I called PartSelect and bless their soul they sent me a new one under warranty. I didn't even have to ask for it. Their turn around time was the same as before and within two days not counting the weekend the oven lit like a Christmas candle. Thanks to all before me who shared their experience. Curious though why no one mentioned the splicing method.

PriceSelect was the best. Special thanks to them.

Replacing the igniter itself was a simple matter a few screws holding its housing and then plugging the new one into the connector. Difficulty came trying to figure out how to access the igniter. Disassembling the floor of the oven was a dead end involving many screws. Pulling the unit out from the wall was a big job and another failure. ... Read more The problem was solved with the removal of the drawer. Underneath, in the rear was a sheet metal plate held by 2 screws. Behind that hung the igniter connection. Voila! Job done.

Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new m ... Read more odule the burners have never worked so well.

Took bottom oven pan off accessed through oven storage drawer.Removed a few screws holding the igniter bracket,removed igniter from its holder(Be really,really careful doing this procedure because the igniter tip is verrrrry fragile,ask me how I know)Put it all back together and Voila,it works!This is so easy a job a caveman can do it! G ... Read more ood luck!

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

removed two screws from each burner, removed ignitor wires from burners, pulled range top removed old module and inserted new reattaching wires for four burners, switch and power to new module. reset top, attached wires to burners and reinserted screws

Part Select was a great site for diagnosing the problem and providing the schematics of the range.
The part arrived quickly. All we had to do is pull off the old knob and replace it with new knob by pushing it on the rod that connects and controls the thermostat.

Removed 3 screws, lifted the top control panel. Adapted new plastic end panel and replaced new end cap an refastened with original screws.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire ... Read more within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.

I have an older model gas oven which required that all screws had to be removed. With a screw gun the job would not haven taken long. Once the bottom pan was removed the oven ignitor took some finese to remove. This was only due to the short wires. Once pulled sufficiently to be able to disconnect the ignitior (although I was afraid I ... Read more was going to pull the wires and separate them from the stove), it was very simple to unplug and plug in the new one (again, making sure to hold the plug so the wires would not retract back behind the wall which would have required the stove to be pulled out from the wall and the back disassembled).

The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.

My repairman told me it was probably the ignitor (even though the old one sitll glowed), but after weeks of waiting for his back-ordered part, I decided to try it myself - found it on PartSelect and had it 3 days later. Turned off the power to the oven. Slid out the 2 racks, and the cover below the racks. Unscrewed 1 nut and removed th ... Read more e V shaped metal plate that distributes the heat. Under that removed 3 screws that hold the ignitor clip in place and got the igniter out of the clip. I couldn't get to the plug on the other end of the ignitor until I took out the oven drawer and removed 2 screws holding a metal cover in place below the oven. Reversed the whole process being careful with the end of the new ignitor (I read it was fragile). The oven now heats up in 5 minutes and maintains temperature again!

WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove. ... Read more r />Needed flashlight to see under stove.

Read less