AP44000 Whirlpool Ice Maker - Instructions

I determined that the plastic lever inside the icemaker was broken and I found the part easaly. It was farelly inexpensive considering the important job the ice maker does, so I order it and paid for the standard, 5-8 days delivery. To my surprise, it was delivered (to my neighbors house thanks to the delivery person) the next day. Onc ... Read more e Berry the neighbor delivered it to my house, 15 minutes later ice was being made. I had to remove one screw and losen two on top of the icemaker, disconnect power and remove the icemaker. I don't think that this step was even required but I wanted to remove all of the old ice from the maker without thawing out the freezer. Replacing the part itself also required removal of three screws. I think that almost anyone can do this easily (with or without Berry).

replaced moduale, work just like new.

My husband is a plumber...but did not have time to make the repair. So I took it upon myself!

Super Easy!

1. Unplugged Fridge
2. Unscrewed the 3 screws on motor
3. Pulled out old motor
3. Had to pour some hot water to melt ice cubes that were currently in the shoot. (because the new part would no ... Read more t line up correctly because of the frozen cubes inside the maker). Then soaked up all the water with towels.
4. Inserted the new motor
5. Put 3 screws back in.

ICE, ICE BABY! Within a couple hours it was dropping ice into the bucket! Husband came home, and I told him I fixed the ice maker (his expression was of dread)...and then he checked it out and all was perfect! So proud!

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started ... Read more making ice in about 15 minutes. very easy fix

Pulled off plastic cover on motor, removed 3 screws and removed old motor. installed new motor making sure control arm lined up in slot. be sure to disconnect power before doing this job !!!

removed front cover installed gearbox then attached lift arm plugged in frig turned on h2o and now i have plenty of ice ! ordered part on Saturday got part on monday in the mail and had ice by supper what a great place to shop and the service was great and parts made easy to find on the website. thank you very much! I will refer your bus ... Read more iness to all my friends.

I ordered the part and just 1 1/2 days later, it arrived! Awesome!

I took the cover off the ice maker motor. Then I simply unscrewed the three screws holding the motor in place (be VERY careful - the hinge mechanism that holds the ice maker on/off bar needs to be gently removed from the motor so the prongs do not break).
< ... Read more br />Once the motor and ice maker hinge were removed, I simply pushed the new motor on, screwed all three screws back in, put the cover back over the motor, pushed the bar to 'on' and water flowed and ice was made! I turned it to Max so I would have lots of ice in a short amount of time then returned the switch to Normal and I've not had a problem since.

3 Years ago our icemaker stopped working and we paid a professional $225.00 to come and repair. This time I chose to investigate the problem on line and PartSelect website gave me info on the motor assembly that may be the problem. Sure enough I purchased the part, it was delivered in two days. My husband installed the control & motor ass ... Read more embly in less than 15 minutes. We had ice within hours. Thanks for saving us a service call and the expense. The Goldbergs

replaced icemaker motor.easy peasy

Remove the ice maker with two screws in the side and one screw in the bottom. You don't have to completely remove the side screws but you do have to remove the bottom screw.
Lift up on the ice maker and reach behind it and unplug the wiring harness. The tube that lets the water in is accessible from the rear of the fridge. Remone th ... Read more e water line, its only finger tight, and remove the two screws. Pull the tube up and out. Thaw it out with hot water and reinstall. With the ice maker out and on the table, pop off the front cover. Remove two phillips head screws and slide the cube tray off. watch how everything is placed before you slide it off. Slide on the new tray and reinstall all screws. Reassemble in reverse order that you took it out. Your ready to make ice...

Went very easy, watched the video from the web site and did what it showed to do and put it together and it worked.We now have ice.

Removal of the Ice Maker required the removal of only one screw from underneath the maker and the power connector disconnect. Dis-assembly was straight forward. Remove old tray and heater, and reassemble with new tray and heater unit. Reinstall Ice Maker! Special Note: Allow the Ice Maker time to cycle through it's sequences. It may ... Read more take a period of time before it starts producing ice after re-installation.

This water valve is slightly different from the original on my older GE refrigerator (i.e., the mounting bracket is larger and oriented differently, thus doesn't fit). To still use the part, I first tried mounting the new valve on my original bracket, but this resulted in a sideways mounting of the solenoid/magnet valve. This orientatio ... Read more n generated a slower and noisier water pumping action (the solenoid/magnet valve is assisted by gravity, so it needs be installed with the top of the solenoid facing up). Then I opted to use the original valve plastic housing and bracket and switch out all rubber seals and gaskets and the enitire solenoid/magnet assembly from the new one. This worked like brand new.

I removed the two screws that hold the ice maker door. I then removed the single screw on the right underside of the ice maker. I depressed the plastic "catch" on the left underside of the assembly and the whole thing just pulled straight out. I then disconnected the wire harness.

The module cover is removed, then the module it ... Read more self is easily removed by removing three screws.
The assembly is just as easy.

A few hours later, I had a half bucket of ice!

The first thing I would like to say is thank you Parts select for a very fast delivery. It was within 24 hours I received my component. The installation went very well. The main thing is to take each part off the old mold, one at a time and install it onto the new mold. Make sure to look at each part as it is mounted to the old mold an ... Read more d re install them the exact same way. Just be gentle with some of the plastic pieces because they are fragile in certain areas. It will take a few hours for everything to start working properly. Thanks again Parts select. Good luck and God Bless.