AMV52 - Parts

This high-voltage diode is designed for use within various makes and models of microwaves and is a genuine OEM part that converts alternating current (AC) into direct current (DC). If you notice your microwave turns on and starts but does not heat anything, this diode is likely responsible. You can check the continuity of the diode with a...Read more multimeter before outright replacing it, but it is important to remember that doing any repairs on a microwave and dealing with sensitive electrical components should be done carefully and with the appropriate precautions to avoid any hazards. To replace the high-voltage diode in your microwave, disconnect it from power and allow it to discharge. Using the appropriate screwdrivers, gain access to the control panel of the microwave. Using an insulated screwdriver, release any electrical charge in the capacitor by touching it across the terminals. Then you can remove any hardware securing the diode, including the harness connecting it to the capacitor, which may be easiest done with pliers. Connect the new diode to the capacitor terminal and the securing bracket, and then reassemble your microwave before connecting it to power again.

This part is a genuine manufacturer door interlock switch kit, also known as primary micro switch or microwave switch kit, for a microwave. The function of this part is to sense when the door of the microwave is open or closed. If the part is defective, the microwave will not start or will start when door is open. This kit contains two 15...Read more Amp, 125/250 Volt switches with 3/16 inch terminals. Be sure to disconnect power to microwave before replacing part. Use extreme caution when replacing microwave parts, as high-voltage capacitors can retain an electrical charge when unplugged. NOTE: This kit includes 2 single pole, double throw (SPDT) micro switches. As per the manufacture for the secondary interlock switch order part # 56001100.

Sold individually. For white and almond models.

This is a mounting bracket for a microwave. The part is fitted between your microwave and wall to allows you to secure your appliance safely to the wall studs and install it above your range. It is made entirely of metal and has holes throughout the length of the part so you can choose to put screws where the wall studs are. This ensures ...Read moreperfect installation. The bracket measures 13 inches in diameter. Be sure to have someone help you secure the microwave to the wall. This is a genuine OEM replacement part. Hardware is not included.

Featuring a bright, clear light, this genuine Samsung Halogen Bulb is ideal for illuminating the cooking area in your microwave for enhanced visibility. Designed with safety and quality in mind, it is imperative to use this Samsung-approved accessory for guaranteed compatibility and performance. The high-quality nature of this part ensure...Read mores ease of installation across a majority of Samsung microwave models. However, a new socket may be necessary for this halogen lamp. Installation should be carried out by a trained technician due to high-voltage components within the microwave, unless specified otherwise in your owner's manual. Please ensure your model compatibility before purchasing.

This is the replacement charcoal filter for your microwave. It is black in color and measures approximately 11 inches by 2 ½ inches. The charcoal filter removes cooking odors from the air that circulates through the microwave vent. You will likely need to replace the charcoal filter if you notice any damage to it, or if it has been in yo...Read moreur microwave for a long time. This part is sold individually and is and authentic OEM part sourced directly from the manufacturer.

This rivet is used for the stirrer cover/wave guide. They are sold individually.

This is a high limit thermostat designed for use within various models of microwaves. The purpose of a high limit thermostat is to open the circuit of the appliance when the internal temperature reaches a certain threshold, to avoid becoming a safety hazard. If this thermostat fails or is damaged, it will cause your microwave to stop oper...Read moreating entirely. This is not to be confused with a thermal fuse, which is a one-time use component, whereas this high-limit thermostat resets once it drops back below operating temperatures. But if your microwave has repeatedly shut off, it is defective, or if the manufacturer recommends you replace it after it is triggered, it needs to be replaced immediately for safe operation. Consider inspecting your microwave for other component damage or factors that could lead to your microwave overheating, because that is what is causing this thermostat to be triggered. Replacing the high-limit thermostat will require a flathead and/or Philips-head screwdriver to remove the cover for the electronics of the microwave. First, you will want to unplug your microwave from the wall outlet and use your screwdriver to remove the side/top cover to give you access within it. Using your user manual, locate the thermostat within the main panel assembly and disconnect it from the wire harnesses, which may require a set of pliers. Here you can inspect it and any other components for visible burn damage. You can also test this thermostat for continuity with a multimeter, to see whether it is burnt out or perhaps defective. Install the new thermostat in place and reassemble your microwave, and you can now microwave safely.

This genuine OEM light socket provides power to the light bulb in your microwave while holding it in place. This light socket is two pronged and the bulb should screw easily into it. If your light bulb will not light, check the bulb itself and light socket’s connection. If the socket is broken, or faulty it should be replaced immediately....Read more Make sure to remove the high-voltage capacitor from your microwave before beginning this repair.

This magnetron in your microwave creates the radiation needed for cooking or warming your food. It is located inside the main cavity, typically near the transformer or waveguide. When the magnetron becomes defective, your food may not heat up properly or heat up at all. Additionally, buzzing or humming sounds may be noticeable while the m...Read moreicrowave is in operation. With a malfunctioning magnetron, your microwave loses its primary function. To remove it, you first need to unplug your microwave from its outlet. Before touching any components, discharge the capacitor by placing a screwdriver, with an insulated handle, across the two terminals of the capacitor. Once the capacitor is discharged, replace the current magnetron by disconnecting it from any wires and removing any mounting screws or clips. This magnetron is sold individually and is supplied directly from the original equipment manufacturer.