AMV116 - Instructions

Removed top vent panel....black plastic runs the length of the microwave....3 Phillips screws. Removed front right panel one Phillip screw on top right. Lift up to remove lifts off the catches. Unplug some of plug connectors on the back of the control circuit board to have room to swing it out of the way to gain access to the interlock s ... Read more witches. Take pictures of all disconnections and wire connectors removed from switches. There or two interlock banks of switches my problem was the top one. Remove the switch bracket held in with one star drive screw and a plastic catch on the switch bracket actuator...there is a slot in the frame the actuator slides into. Replace switches and reverse procedure to reassemble.

Read some instructions and easily found the fuse. Replaced it. Still didn't work. Took control panel off to check door switches. Nothing I read mentioned a second fuse. Tested and it to had blown. Ordered another one. Popped them in. Done.

Replaced both switches on the top door latch. Diagram shows the two switches on the lower latch? No success. Still had same message on the display. Replaced lower switch, fixed the issue.

After determined the problem on one of the websites...I received the part I needed... removed the control panel and installed the new main fuse In about 15 mins!

I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to cat ... Read more ch enough to hold the glass plate in position and left it at that.

Remove two screws from Vent Grille, one on either side, and remove one screw inside Vent Grille on right side. Pull Vent Grille off exposing the two Charcoal filters. Remove the two Charcoal filters by hand and replace with new ones. Reinstall the Vent Grille and tighten screws. That's it. I'm not handy (ask my wife) and if I can do ... Read more it so can you.

BEWARE: KMHS120ESS takes two charcoal filters. This site doesn't tell you that! I only figured it out after ordering one, receiving it, and removing the vent cover to replace it. So then I had to order another one and pay for shipping a second time (which cost almost as much as the filter itself). C'mon PartSelect, why are these not sold ... Read more in a pair?

The original bulb came apart while unscrewing it from the back of the microwave, leaving the metal screw thread contact still in the socket. Since this is an over-the-range micriwave there isn't enough room to manuever needle nose pliers into the socket to remove the screw thread contact. So this is how we were able to remove it.
U ... Read more nplug power cord.
Take a standard wine bottle cork and whittle down one end until it fits in the socket. Then, using a bit of pressure push the cork into the socket snd begin unscrewing the screw thread contact until it comes out of the socket. Works like a charm!

The hard part was trying to find the light bulb locally. The locally sold light bulbs were either too long, not dual element or not powerful enough. So I ordered the light bulb straight from PartSelect. When it came time to install the new light bulb I carefully removed the screw holding the plate in position so as not to loose it in my ... Read more gas stove. I needed the mirror to line up the light bulb and screw it in. Once it was in I verified operation and closed up the plate being careful not to drop the screw into my gas stove. Problem solved.

issues started when door opened light would flicker then come on disassembled checked switches with a meter determined switch was faulty figured I'm in here replace them all because if one fails others will follow be careful removing actuator assembly plastic is brittle (remember this is above the stove subject to heating and cooling) pla ... Read more stic isn't as pliable installed all the switches perfecto oh by the way disassembled the faulty switch found contacts had arced from opening door while microwave is running use the buttons to stop will eliminate further issues

I used a Google search to show how to access the area behind the front panel. There was a folded paper copy with a schematic and wiring diagram in that space.Then I used a multi-meter to determine which of the THREE micro-switches was causing the problem. I called your help line and ordered a replacement switch. The switch was delayed ... Read more in transit so your agent credited me with the cost of shipping.

When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.

All seems to be working well now.

Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?

I looked up a YouTube video of someone with a similar over the oven microwave. That helped me get into the area behind the control panel where the door switches are. I checked the springs and the cam rocker? The thing that actually hits the button on the switch when the door closes. They were in good condition so I assumed the door switch ... Read more was bad. There are two so I just purchased one figuring (hoping) that only one was bad. And lo and behold only one was bad. Bing bam boom. Put it all back together and I'm set. Not too difficult. Took a week of work because it takes like 50 days to ship. My kitchen looked like a hurricane after image because of all the parts scattered everywhere.

Simply need a Phillips head screwdriver, remove the screen covering the light bulb. all you need to do is unscrew burned out bulb and screw in the new bulb. Much easier to order the bulb in the socket and pull it out the socket and plug in the new socket and bulb. because you have a limited space to work

I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.

Got some info from the PartsSelect web site and a short YouTube video about how to replace the socket. (Even at 74 years old I'll be darned if I'll pay for a service call if I think I can do the repair myself). Unfastened all the panel screws, swung down the rear-hinged lower panel carefully, then took a couple of pictures showing which w ... Read more ires went to which side of the light socket -- and to the underside of the turntable because those pulled off by themselves when I lowered the panel). Pried off all the silicone sealer around the socket using my fingers, got the old socket out and replaced it, put the wires back in place, refastened the drop-down panel. It was a very easy, straight-forward task that would have taken <15 minutes were it not for the fact that my old eyes had trouble seeing all the screws, even with a flashlight. Everything works fine now.