ALW8 Amana Washer - Instructions

I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot

Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.

Dismantled the washer and cleaned out pump. Since cover-out ring was damaged, replaced it while I had the washer apart.

replaced belt that was wore out. decided to replace pump while I had washer apart.

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remov ... Read more e the part but putting the new agitator on was simple.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

Since the agitator and bell housing seperated as once piece from the drive shaft I didn't have to remove them and the schematic showed how the agitator snapped on to the bell housing and the parts I needed for the fix. The new seal went on with no problem, I just used some of the supplied grease on the tight spots. The hardest part w ... Read more as attaching the bell housing. It came to within an inch of the top of the shaft with no problem with a rubber hammer. But the top screw shroud broke when I tried to hammer it the rest of the way using a wood dowel and a block of wood. I couldn't even get the threads of the supplied screw to even touch the drive shaft. So I bought a longer (1 inch) cap screw from the hardware store and added a washer and suplied ring. After torqing it to 5 ft-lbs instead of the 10-20 the plastic beneath the screw was looking kind of thin and stressed and I was afraid of it breaking through or the screw snapping off in the shaft, so I left it alone and used some silicone caulk to seal in the plug that goes in on top of the screw since the side of the shroud broke off. I slipped on the agitator and am testing a load now as we speak. If I get ten more years out of the washer it will definitely be worth the $100 in parts and shipping !

Fixed the problem easy to do just take your time putting in bearing in plastic tub

Laid washer back on a appliance dolly, removed the front cover, checked to see if the hose was touching the motor mount (it was). Removed the drain hose from the pump and standoffs, removed the hose and disk from the back of the washer that holds the hose. Replaced the hose on the pump, turn the standoff to move the hose farther from the ... Read more motor mount, and install it in the disk. May be easier to measure the hose and do the disk first as it is not easy to get the hose bent when it is installed first on the pump.

I opened the bottom and found the belt had broke in half. i ordered a new belt from Maytag online and found a you tube video that showed exactle how to change it. the only thing i had to do afterwards was tighten the tensioner.eazy pezy!

My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.

The instructions included were very good. The biggest problem I ran into was removing the inner tub from off the hub. Using PB Blaster was the trick there, but still took some effort to finally pry it lose without damage. The hub screwed right off after and removing the Triple Lip Seal was easy enough with screw drivers. Cleaned things up ... Read more and replaced it by gently tapping around it to seat it evenly. Reassembly also went well, but I DO HAVE a story. Being as careful as I thought I could be, I still somehow broke the outer tub. I read about others experience, buying and using JB Weld WaterWeld to fix it. Now the washer is so quiet again that you have to look into the drain tub to see if it is spinning. AWESOME

Removed the plate screws. Found valve, unplugged wires, removed hose and replaced reattaching everything. Replaced plate. Done

Took off part and replaced it very easy instructions.